Dodge 2011 Grand Caravan Owner'S Manual Download Page 225 | Manualshive

Page: 225 / 562

background image

NOTE:

In the event of an individual being locked inside

the storage bin, the storage bin cover can be opened from
inside of the bin by pushing on the glow-in-the-dark
lever attached to the storage bin cover latching
mechanism.

Coat Hooks

Coat hooks are located along the headliner for the second
and third row seating positions. The coat hook load limit
is 10 lbs (4.5 kg). Exceeding the recommended load limit
can cause the coat hooks to break or disengage from the
vehicle.

Storage Bin Cover Emergency Release Lever

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

223

«
...
223
224
225
226
227
...
»

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Grand Caravan

Brand: Q'STRAINT Pages: 10

YARIS LIFTBACK 2009

Brand: Toyota Pages: 13

Brand: Westfalia Pages: 71

1973 Crown Hardtop

Brand: Toyota Pages: 50

Brand: Subaru Pages: 99

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

MagicComfort MSH200

Brand: Waeco Pages: 108

Brand: Tusk Pages: 2

Brand: AC Schnitzer Pages: 16

Brand: Quadratec Pages: 8

MCL-7000 Series

Brand: Dakota Digital Pages: 2

Brand: Volvo Pages: 284

Brand: Road Ranger Pages: 22

XEBRA ZAPCAR Series

Brand: Zap Pages: 16

Brand: BrandMotion Pages: 6

Brand: Tesla Pages: 274

Brand: Mazda Pages: 3

Brand: Z Flash Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands