Dodge 2006 Caravan Manual Download Page 308 | Manualshive

Page: 308 / 504

background image

CAUTION!

To prevent damage to the starter, do not crank the
engine for more than 15 seconds at a time. Wait 10 to
15 seconds before trying again.

If the engine has been flooded, it may start to run, but not
have enough power to continue running when the key is
released. If this occurs, continue cranking up to 15
seconds with the accelerator pedal pushed all the way to
the floor. Release the accelerator pedal and the key once
the engine is running smoothly. Do not overspeed en-
gine.

If the engine shows no sign of starting after two 15
second periods of cranking with the accelerator pedal
held to the floor, the “NORMAL STARTING” procedure
should be repeated.

After Starting

The idle speed will automatically decrease as the engine
warms up.

308

STARTING AND OPERATING

«
...
306
307
308
309
310
...
»

Summary of Contents for 2006 Caravan

























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2006 Caravan

Brand: AAMP of America Pages: 6

Brand: DAVIS Pages: 32

Brand: FormFit Pages: 2

Brand: Trailboss Pages: 5

PRIME DESIGN VRR-NV200

Brand: Safe Fleet Pages: 12

Brand: Thule Pages: 8

Brand: Ecco Pages: 9

V70XC Cross country 1998

Brand: Volvo Pages: 262

Brand: Cadillac Pages: 352

Brand: Audiovox Pages: 3

Brand: Victory 4x4 Pages: 9

nERGY ETSA200R-PA

Brand: Soundoff Signal Pages: 3

Brand: Truma Pages: 10

Brand: Sintrones Pages: 55

Brand: Chevrolet Pages: 46

Brand: Connects2 Pages: 2

Brand: Metra Electronics Pages: 12

Brand: Saab Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands