Dodge 2006 Caravan Manual Download Page 54 | Manualshive

Page: 54 / 504

background image

should be used only if the existing belt is not long
enough. When it is not required, remove the extender
and stow it.

WARNING!

Using a seat belt extender when not needed can
increase the risk of injury in a collision. Only use
when the lap belt is not long enough when it is worn
low and snug, and in the recommended seating
positions. Remove and store the extender when not
needed.

Driver And Front Passenger Supplemental
Restraint Systems (SRS) — Airbags

This vehicle has airbags for both the driver and front
passenger as a supplement to the seat belt restraint
systems. The driver’s front airbag is mounted in the
center of the steering wheel. The passenger’s front airbag

is mounted in the instrument panel, above the glove
compartment. The words SRS AIRBAG are embossed on
the airbag covers.

NOTE:

The front airbags are certified to the Federal

regulations that allow less forceful deployment in low
speed collisions.

Front Airbag Components

54

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
52
53
54
55
56
...
»

Summary of Contents for 2006 Caravan

























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2006 Caravan

Brand: Metra Electronics Pages: 14

Brand: UMBRA RIMORCHI Pages: 18

Brand: Buick Pages: 428

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

Gasoline/Electric DS Golf Car 1996

Brand: Club Car Pages: 48

Brand: Phonocar Pages: 2

Brand: Dacia Pages: 238

Brand: Cadillac Pages: 20

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: Velleman Pages: 12

Brand: Honda Pages: 22

Brand: Mercedes-Benz Pages: 494

Prime Design VBI-FT31B

Brand: Safe Fleet Pages: 12

Brand: Whispbar Pages: 14

Brand: Pet Gear Pages: 4

IGNIS 2022 Series

Brand: Suzuki Pages: 570

2005-2009 Chrysler 300C

Brand: Mopar Pages: 7

2008 Savana Van

Brand: GMC Pages: 402

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands