Dobot Magician Lite User Manual Download

Page: 69 / 72

Dobot Magician Lite User Guide

Operation

Issue V1.9.1 (2020-01-11)

User Guide

of the text.

Click

Start

to start writing on the paper.

When writing, click

Pause

to pause the writing and

Stop

to halt the writing.



NOTE

You can click

Download

to download the file to Magic Box or Magician Lite to perform

in offline mode. For the detail, please refer to 5.4Working in Offline Mode

Operating Blockly

Blockly is a programming platform for Magician Lite based on Google Blockly. You can

program through the puzzle format, which is straightforward and easy to understand.

Prerequisites



Magic Box + Magician Lite has been powered on.



Magic Box + Magician Lite has been connected to DobotStudio successfully.

Procedure

The

Blockly

page is displayed.

Figure 5.55 Blockly graphics programming

Table 5.11 lists the description of blockly module.

Table 5.11 Blockly description

No.

Description

The selection area of blockly module, including

logistic, loop, math, and Dobot API. You can program

by dragging them to the window

The window of blockly programming

Summary of Contents for Magician Lite









































































Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands

Dobot Magician Lite, User Manual

Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands