background image

 

ArtNet Player 4

 

14 

 

CE-Conformity 

 
 

This assembly (board) is controlled by a microprocessor and 
uses high frequency. In order to maintain the properties of the 
module with regard to CE conformity, installation into a closed 
metal housing in accordance with the EMC directive 2014/30/EU 
is necessary. 
 
 

 

 

Risk-Notes 

 
You purchased a technical product. Conformable to the best available technology the 
following risks should not excluded: 

 

 
Failure risk: The device can drop out partially or completely at any time without 
warning. To reduce the probability of a failure a redundant system structure is 
necessary. 
 
Initiation risk:  For the installation of the board, the board must be connected and 
adjusted to foreign components according to the device paperwork. This work can 
only be done by qualified personnel, which read the full device paperwork and 
understand it. 
 
Operating risk: The Change or the operation under special conditions of the 
installed systems/components could as well as hidden defects cause to breakdown 
within the running time. 
 
Misusage risk: Any nonstandard use could cause incalculable risks and is not 
allowed. 
 
Warning: It is not allowed to use the device in an operation, where the safety of 
persons depend on this device 

 
 
 
 
 
 
 
 
 
 
 

ArtNet

 

is a trade mark of Alderamin Group Ltd.  Designed by and Copyright Artistic Licence Holdings Ltd. 

 

Summary of Contents for ArtNet Player 4
















Reviews: