Installation
Connect a Class 2 power supply with 12
-
24 VDC output voltage to the input connector of Scene10cas. Make sure not to use a constant current LED
driver and make sure that the cable polarity is correct. The product has two DMX input connections (+ and
-
), plus one common (RETURN) ground.
Connect the DMX in wires to a DMX master of your choice to give you DMX control of your Casambi Scene lighting network. Add Scenes to the
Casambi network, the SceneDMXcas will allow up to 20 Scenes to be selected.
Using the Casambi app, go to Gateways, and press on the SceneDMXcas device, and add it to your Casambi network. Now press on the
SceneDMXcas icon, and scroll to the bottom of that screen. Note at the bottom of this screen there are 21 user programmable parameters—DMX
Start Address, and 20 Scene selectors. First select your DMX Start Address, then up to 20 Scenes from your pre
-
defined Scenes in your Casambi
network. Now simply use your DMX master to select the Scene and Intensity, with the first DMX channel selecting the Scene and the second chan-
nel defining the Intensity.
SceneDMXcas should not be placed in a metal enclosure, such as metal junction boxes. Metal will attenuate radio signals which are crucial to the
operation of the product. If the product will have to installed into a junction box, make sure to use a plastic junction box. SceneDMXcas is an ETL
Listed Open
-
Type device which means that it will have to be used together with a Class 2 power supply with maximum output power of 100 VA. The
product can be installed outside of junction box. Make sure to comply with National Electric Code in installation and when selecting installation
wires.
Range
The range between two SceneDMXcas
’
s or between a SceneDMXcas and a smart phone can vary depending on obstacles and surrounding material.
In open air the range between two SceneDMXcass can be in excess of 200 ft, but if the unit is encapsulated into a metal structure, the range can be
only few feet. Therefore, thorough testing is high suggested.
Casambi uses mesh network technology so each SceneDMXcas acts also as a repeater. When testing the network, it is important to test that each
unit can be controlled from any point of the network covered area.
Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)
This device may not cause harmful interference, and
(2)
This device must accept any interference received, including interference that may cause undesired operation.
Warning
Changes or modifications not expressly approved by DMX Engineering and Design LLC could void the user
’
s authority to operate the equipment.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement for Canada
This device complies with Industry Canada
’
s licence
-
exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment is exempt from the routine RF exposure evaluation requirements of RSS
-
102. This equipment should be installed and operated with a minimum dis-
tance of 20 cm between the antenna and the user or bystanders.
Le présent appareil est conforme aux CNR d
’
Industrie Canada applicables aux appareils radio exempts de licence. L
’
exploitation est autorisée aux deux conditions sui-
vantes:
(1) l
’
appareil ne doit pas produire de brouillage;
(2) l
’
utilisateur de l
’
appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d
’
en compromettre le fonctionnement.
Information in this document is subject to change.
Copyright DMX Engineering LLC 2019
-
2020
SceneDMXcas User Guide v1.04 USA and Canada
DMX Engineering LLC
9221 E. Baseline Road, Suite 109
-
492
Mesa, AZ 85209
**RATED FOR INDOOR USE ONLY**
