background image

6

UNPACKING THE TISSUE PULLER SYSTEM

UNPACKING THE TISSUE PULLER SYSTEM

Take a few minutes to carefully inspect your new Tissue Puller System - 560TP for damage which may have occurred during 

handling and shipping. If you suspect any kind of damage, please contact DMT immediately and the matter will be pursued 

as soon as possible. If the packing material appears damaged, please retain it until a possible claim has been settled. We 

recommend that you store the packing material for any future transport of the 560TP System. In case of transport and the 

original packing material is unavailable, please contact DMT Sales Department for advice and packing instructions. 

After unpacking your new 560TP System, please use the following list to check that the system is complete: 

• 

1 Tissue Puller - 560TP System unit (electromechanical)

• 

1 USB cable 

• 

1 power cord* (24V Powerconverter)

• 

1 box with mounting hook or other customer defined mounting supports

• 

1 calibration weight 5g weight

• 

1 Allen key

• 

1 CD with MyoPULL Software (Windows 7)

• 

1 CD with User Manual

* The shape of the AC plug varies by country; be sure that the plug fits the outlets for your location.

Summary of Contents for 560TP



















Reviews: