background image

Installation & Operation Manual  

                                                                                  

Mini Merlin 

 

Rev: 11   09-20 

10  

   Auto Reset & Buzzer Switches 

 
There are two dip-switches on the circuit board. 
 

 

ON 

OFF 

Auto Reset 

In the event of a power loss – the mini merlin will 

restart automatically when power is restored.  

In the event of a power loss – the mini merlin will 

need to be reset manually when power is restored. 

This is the factory set condition. 

Buzzer 

The buzzer will sound every 15 seconds during 

pre-alarm and continuously at alarm level. 

This is the factory set condition. 

The buzzer will not sound at any gas level. 

 

   Building Management System Integration 

 
This device can be integrated with a Building Management System (BMS), a home alarm 

system, or be used as part of a boiler low voltage safety limit to make or break a circuit on both 

gases separately, (valve open or valve closed) depending on the system. 

 

These switches can be used for a variety of purposes including triggering alarm contacts, 

operating and external relay for multiple appliance shut-down and generating status signals for 

a BMS system. 

 

   Specification 

 

Product:

  Mini Merlin  

Version: 

CH4CO 

Display 

1.8” TFT – Thin Film Transistor 

Screen Brightness 

Non- adjustable  

Initial Stabilisation Time 

60 Seconds approx. 

Power Input Voltage  

100-240Vac /  50-60Hz 

Valve Output Voltage 

100-240Vac / 50-60Hz 

Fuse 

Anti-Surge 3.15A 250Vac 

Current Consumption 

3W Max  

Accuracy @ 25°C / 77°F 

± <10% 

Operating Temp 

32 – 122°F  30-85%RH Non-Condensing 

Audible Buzzer 

65dB (controlled conditions @ 1 ft) 

Volt Free BMS relay output 

0.5A switching current (resistive load) 

Gas Sensor Type 

Methane: Semi-conducting 
Carbon Monoxide: Electromechanical 

Gas Sensor Measuring Range 

Methane: 500-10,000ppm 
Carbon Monoxide: 0-1000ppm 

Gas Value Pre-Alarm  

Methane: >8% LEL 
Carbon Monoxide: 20ppm 

Gas Value Alarm 

Methane: >10% LEL 
Carbon Monoxide:  

20ppm after two (2) hours 
50ppm after one (1) hour 
100ppm after ten (10) minutes 

300ppm after one (1) minute 

Dimensions (mm) 

95(W) x 140(H) x 60(D) 

Weight  242g approx.

 

X-Cel House, Chrysalis Way, Langley Bridge, 
Eastwood, Nottinghamshire NG16 3RY

+44 (0) 1773 534555
[email protected]
dmsltd.com

Summary of Contents for MINI MERLIN

















Reviews: