background image

ULTIMATE SERIES

COAXIAL CAR AUDIO SPEAKER

WELCOME

Thank you for buying a DLS ULTIMATE speaker.
The ULTIMATE speakers are our best speaker line but a
poor installation job can destroy the final result even from
these speakers. So if you feel unsure, turn over the instal-
lation job to someone better suited to it.

INSTALLATION

Mount the speakers in the door or in the dashboard of
your car. Normally they will fit in the factory pre-made
mounting holes. If you want an improved sound,
reinforce with a baffle of MDF-board or similar. An instal-
lation high up on the door side is to be prefered. An
alternative installation is in so called kick panels down on
each side of the floor with the speakers facing up- and
inwards towards the listener.
It is important to fasten the speakers properly in order to
avoid bad sound or rattling.
For speakers with separate filters in boxes or similar it is
vital that they are attached properly to the interior of the
vehicle to avoid rattling. Don´t place them close to the
internal wiring of the car, this can cause interference.
Avoid to install filter boxes in the door sides because
they can easily be broken because of rattling or
moisture. Make sure the cables don´t get jammed
causing a short circuit to ground. This can damage the
output circuits of the head unit or amplifier.

RUNNING-IN PERIOD

Allow the speakers to play for at least 15-20 hours. After
this time the performance is correct.

CONNECTION OF SPEAKERS

Make sure you connect the cables with correct polarity
to the speakers. Observe the markings on the terminal.
Use high quality speaker cables like DLC SC 2x2,5,
SCP 2x2,5 or similar.

UX26

 

 

 

 

 

 

Technical Assistance

For technical assistance, ask the shop where the
product was sold, or the distributor in your very
country.You can always send an e-mail to 

[email protected]

and ask for help. Information can also be found on our
WEB-site www.dls.se
We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.

DLS Svenska AB

P.O.Box 13029

SE-40251 Göteborg, Sweden

Phone: +46 31 840060, fax: +46 31 844021

E-mail: [email protected]

www.dls.se

TWEETER LEVEL SELECT

Select tweeter  level in four steps by moving the small  jumper  inside
the filter box.  

+2 dB -  0  -  -2 dB  -  -4 dB

FACTS DLS UX26 COAXIAL SPEAKER

Size

6,5" ( 16,5 cm)

Nom. power (RMS)

100 Watts RMS

Maximum power

160 Watts

Frequency range

45 Hz-25 kHz

Sensitivity

91 dB / W / m

Magnet diameter

58 mm / 2,28”, neodymium

Outer diameter

165 mm / 6,5”

Mounting depth

63 mm / 2,48”

Mounting hole

140 mm / 5,5”

Voice coil

52 mm / 2”  aluminium flat wire

Tweeter

28 mm /1,1”, nanoplate tweeter

SPEAKER PHASING

To be sure to have the correct speaker polarity (phase) you can
check this by using a 1,5 Volt battery.
Connect a cable from the battery plus-pole to the speaker plus,
and a cable from the battery minus to the speaker minus.
If the speakers are correctly connected the speaker cone should
move outwards on both right and left channel.
This check must be made on the cables going from the speakers,
to the output terminals of your car stereo or amplifier.

Filter connection UX26

Bilstereo /
förstärkare

Tweeter
 Nivåval

- 4

- 2

  0

+2

 

     +INPUT-   + W -     + T -

Tweeter

Woofer

12

12

12

12

+

+

-

-

Reviews: