Model
Woofer
Mid
Tweeter
Nom.
Max
Sensi-
Magnet
Inst.
Mounting
Crossover
power
power
tivity
size
depth
hole
UP5
13 cm / 5,25”
28 mm / 1,1”
120 W
180 W
89 dB
62 mm / 2,44”
58 mm / 2,28”
120 mm / 472”
Separate box
UP6
16,5 cm / 6,5”
28 mm / 1,1”
150 W
180 W
88 dB
62 mm / 2,44”
63 mm / 2,48”
140 mm / 5,5”
Separate box
UP35
13 cm / 5,25”
2,5”
28 mm / 1,1”
120 W
180 W
89 dB
62 mm / 2,44”
58 mm / 2,28”
120 mm / 4,72”
Separate box
UP36
16,5 cm / 6,5”
2,5”
28 mm / 1,1”
150 W
180 W
88 dB
62 mm / 2,44”
63 mm / 2,48”
140 mm / 5,51”
Separate box
UR5
13 cm / 5,25”
28 mm / 1,1”
80 W
120 W
91 dB
85 mm / 3,35”
62 mm / 2,44”
120 mm / 4,72”
Separate box
UR6
16,5 cm / 6,5”
28 mm / 1,1”
100 W
160 W
91 dB
85 mm / 3,35”
65 mm / 2,56”
140 mm / 5,51”
Separate box
UR5S
13 cm / 5,25”
28 mm / 1,1”
80 W
120 W
91 dB
85 mm / 3,35”
62 mm / 2,44”
120 mm / 4,72”
Separate box
UR6S
16,5 cm / 6,5”
28 mm / 1,1”
100 W
160 W
91 dB
85 mm / 3,35”
65 mm / 2,56”
140 mm / 5,51”
Separate box
UR35S 13 cm / 5,25”
2,5”
28 mm / 1,1”
80 W
120 W
91 dB
85 mm / 3,35”
62 mm / 2,44”
120 mm / 4,72”
Separate box
UR36S 16,5 cm / 6,5”
2,5”
28 mm / 1,1”
100 W
160 W
91 dB
85 mm / 3,35”
65 mm / 2,56”
140 mm / 5,51”
Separate box
SPEAKER FACTS FOR DLS ULTIMATE SERIES
RUNNING-IN PERIOD
Allow the speakers to play for at
least 15-20 hours. After this time the
performance is correct.
Filter installation and connection of UP5 & UP6
FILTER/CROSSOVER INSTALLATIONS
CONNECTION OF SPEAKERS
Make sure you connect the cables
with correct polarity to the speakers.
Observe the markings on the
terminal. The small terminal is
minus.
SPEAKER PHASING
To be sure to have the correct speaker polarity (phase) you can
check this by using a 1,5 Volt battery.
Connect a cable from the battery plus-pole to the speaker plus,
and a cable from the battery minus to the speaker minus.
If the speakers are correctly connected the speaker cone should
move outwards on both right and left channel.
This check must be made on the cables going from the speakers,
to the output terminals of your car stereo or amplifier.
Filter installation and connection of UP35 &
UP36 3-way systems
Head unit / amp.
+
-
+
-
2-way crossover
INPUT WOOFER TWEETER
+
-
+
-
+
-
+
-
Bass/mid
Tweeter
TWEETER LEVEL: JUMPER J2
Select tweeter level by moving the small jumper J2 inside the filter
box.
High level
Mid level
Low level
+
+
-
-
The drawing shows the connection of a 3-way system to one channel.
The other channel is connected in the same way. The tweeter level is
adjustable in three steps, the MID level in two steps:
Tweeter level (J3):
High = jumper in HI-position
Mid = jumper in MID-position
Low = jumper in LO-position
Midrange level J2):
High = jumper in HI-position
Low = jumper in LO-position
Jumper J1 is used when you want to run the system without
midbass driver. In this case some components inside the filter
must be disconnected.
Midbass connected:
jumper mounted in IN-position.
Midbass disconnected:
jumper mounted in OUT-position.
NOTE!
If the system is used together with a subwoofer, test to phase reverse the
subwoofer to see what sounds best.
Tw
level
Hi
Mid
Low
J2
BASS
Car stereo / amp.
Speaker impedance 4
Ω
Mid
Bass
Tweeter
+
+
_
_
_
W
oofer
Input
T
weeter
Midr
.
_
Mid level
Coil
HI
LO
J2
IN
OUT
J1
T
weeter level
HI
MID
LO
J3
+
+
