background image

How to install and operate the

Reference RM-series amplifiers

Welcome!

This owners manual is written in easy english and
uses a lot of drawings to simply the installation and
use of the above amplifiers.

Your  Reference series amplifiers must be installed
correctly in order to work well. This manual will show
you how to install the amplifier like a pro. Please
read the entire manual before beginning the
installation.Install the amplifier yourself if you feel
confident  with our instructions and if you have the
proper tools. However if you feel unsure, turn over
the installation job to someone better suited to it.

Warranty Service

This amplifier is covered by warranty, depending
on the conditions in the country where it is sold. If
the amplifier is returned for service, please include
the original dated receipt with the product.

Contents

Features……………………………..

2

Installation…………………….…….

2

Tools and materials needed……….

3

Amplifier installation kit…………....

3

Routing Wires……………………....

3

Wiring

Power and Outputs...…………..….

4

Inputs and controls......…………....

5

High and low level inputs...............

5

Input level control...........................

6

Crossovers, etc..............................

6

Features on each model................

7

RM10 speaker wiring:

Subwoofer.......................................

8

RM15 speaker wiring:

Subwoofer.......................................

9

RM20 speaker wiring:

Front speakers....…...………...…....

10

Subwoofer…………………………...

10

RM30 speaker wiring:

Two speakers and one subwoofer....

11

RM40 speaker wiring:

Four speakers.……………………....

12

Two sp bridged subwoofer

12

Testing………………………………..

13

Troubleshooting……………………...

13

Professional tips……………………..

14

Specifications………………………...

15

(

(

(

(

(

 

 

 

 

 

Technical  Assistance

For technical assistance ask the shop where the
product was sold or the distributor in your very coun-
try. Information can also be found on our WEB-site
www.dls.se
We follow a policy of continuous advancement in
development. For this reason all or part of
specifications & designs may be changed without
prior notice.

DLS Svenska AB

P.O. Box 13029 - SE-40251 Göteborg - Sweden

Tel: +46 31 840060 - Fax: +46 31 844021

E-mail: [email protected]

www.dls.se

This product must be returned to the
separate collection system for electronic
products. Do not dispose this product
together with general household waste.

DECLARATION OF CONFORMITY

DLS amplifiers for vehicles are manufactured in
accordance with the EU directive EEC 95/54 (72/245/
EEC) and are marked with the approval number.
They are also marked in accordance with the WEEE-
directive 2002/96/EC.
The products are also produced in accordance with
the EU RoHS directive 2002/95/EC.

RM10 - RM15
RM20 - RM30

RM40

Summary of Contents for RM10

















Reviews: