TWEETER INSTALLATION T20
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: [email protected]
www.dls.se
Technical Assistance
For technical assistance ask the shop where the product
was sold or the distributor in your very country.You can
always phone the DLS Helpdesk in 46 31
840060 or send an e-mail to [email protected]
Information can also be found on our WEB-site www.dls.se
We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.
WARRANTY SERVICE
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is
returned for service, please include the original dated
receipt with the product.
T20 can be mounted on the dashboard with the plain cup (1), the
angled cup (2), or recessed in a doorside. These tweeters are
included in the R4 and PS4 speaker kits.
SURFACE MOUNTING:
Plain mounting: Use only the plain mounting cup (1) (it´s normally
mounted at delivery). Attach to surface with the two screws or double
adhesive tape.
Angled mounting
:
Remove the plain mounting cup by bending with a
small screw driver in the gap (A). Attach the tweeter element to the
angled cup (2) as shown on picture 3. Pull the cable through the cen-
ter hole. Now the tweeter can be mounted in two different angles.
Attach to the surface with the two screws or double adhesive tape.
RECESSED MOUNTING:
Drill a hole in the door side with a diameter of 48 mm /1,89". The in-
stallation becomes easier if the door side is removed from the door.
Put the two metal wings through the two tracks in the center of the
cup, just as the picture shows, and attach them with the M4 screw
and nut through the center hole. Put the tweeter element into the cup
with the cable going out through the bottom hole. Attach the tweeter
element to the plain cup using the mounting ring (C) attached between
the cup and the tweeter element. The metal wings (B) should be on
the back side of the door panel, holding the cup in place.
A
2
1
3
TWEETER INSTALLATION T25 / UP1C
T25 /UP1C can be installed on the dashboard with the angled cup or
recessed in a doorside with the flush cup.
T25 are included in the DLS REFERENCE speaker kits RS5, RS6,
R5A and R6A. UP1C are included in the MS5A and MS6A speaker kits.
RECESSED MOUNTING:
You need a hole with a diameter of 46 mm
/ 1,81" in the door side (for UP1C 48 mm /
1,89”). Put the two metal wings through
the two tracks in the center of the cup, just
as the picture shows, and attach them
with the M4 screw and nut through the
center hole. The cup is attached to the
door side when the metal wings is pres-
sed to the back side of the door.
Put the tweeter element into the cup with
the cable going out through the bottom
hole. Then attach the element into the cup
and turn it clockwise to attach to the cup.
When removing the element from the cup,
turn it ccw and lift it out
B
C
Size
20 mm / 0,8"
Nom. power (RMS)
50 Watts, 80 Watts max
Freq. range
1,5 kHz-20 kHz
Sensitivity
93 dB
Magnet diameter
20 mm / 0,8"
neodymium magnet
Mounting depth
20 mm / 0,8"
(recessed mounting)
Mounting hole
48 mm / 1,89" (recessed mounting)
Cone material
Silk
FACTS ABOUT DLS T20 TWEETER
A
FACTS ABOUT DLS T25 / T25N TWEETER
Size
25 mm / 1"
Nom. power (RMS)
50 Watts (80 Watts max)
Freq. range
1,5 kHz-20 kHz
Sensitivity
93 dB
Magnet diameter
28 mm / 1,1"
Mounting depth
18 mm / 0,71"
Mounting hole
46 mm / 1,81"
Cone material
Hand treated fabric
FACTS ABOUT DLS UP1C TWEETER
Size
28 mm / 1,1"
Nom. power (RMS)
50 Watts (80 Watts max)
Freq. range
1,5 kHz-20 kHz
Sensitivity
93 dB
Magnet diameter
28 mm / 1,1"
Mounting depth
18 mm / 0,71"
Mounting hole
48 mm / 1,89"
Cone material
Hand treated fabric
SURFACE
MOUNTING:
For angled surface mount
together with the angled cup:
The tweeter element is
attached to the cup by fitting
the three wings on the angled
cup into the tracks of the ele-
ment and then turn it
clockwise. When removing the
element from the cup, turn it
ccw and lift it up.
