Connect to crossover box:
TWEETER LEVEL SELECTOR
Select between four different tweeter levels
by moving the slide switch inside the filter box.
The four positions are: -3 dB, -1,5 dB, 0, +1,5 dB
(RM5.2)
The four positions are: -4 dB, -2 dB, 0, +2 dB
(RM6.2)
Installation of T25 tweeter:
If you plan to use extra baffles for the installation it is very important
that the baffle is stable, but it is just as important that it is shaped
in a way that allows the driver to ”breath” backwards, otherwise
there will be a lack in the drivers bass reproduction.
Art.no
10-21025
Size
25 mm
Impedance
4 ohm
Nom. power
50 Watt RMS
Max power
80 Watt max
Freq. range
1,5 kHz-20 kHz
Sensitivity
93 dB
Fs
1400 Hz
Overall dimensions
43 mm / 1,7"
Magnet
25 mm / 1"
Mounting depth
18 mm / 0,71"
Mounting hole
46 mm / 1,81"
Cone material
Hand treated fabric
Facts DLS T25 tweeter
Installation in baffles:
Wrong way
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
Bad air flow
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
Correct way
with chamfer-
ed edges
Max 5 mm
Free air flow
Correct way
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
Facts DLS RM drivers
RM5
RM6
Art.no, driver
8-21405
8-21406
Size
130 mm / 5,25”
165 mm / 6,5”
Impedance
4 ohm
4 ohm
Nom. RMS power
100 Watt
100 Watt
Max. power
200 Watt
200 Watt
Peak power
400 Watt
400 Watt
Freq. range
40Hz-6 kHz
30 Hz - 6 kHz
Sensitivity
85,7 dB
86,7 dB
Fs
72,7 Hz
51,8 Hz
Qts
0,57
0,51
Vas
4 litres
12,3 litres
Cone material
Aluminum
Aluminum
Magnet size
100 mm / 4”
110 mm / 4,33”
Installation hole
120 mm / 4,72”
140 mm / 5,51”
Inst. depth
72 mm / 2,83”
72 mm / 2,83”
+
-
Mid
T
weeter
+
-
-
Head unit / amp.
Amp Mid-Bass Tweeter
+ - + - + -
+2 0 -2 -4 dB
Tweeter select
+
T25 can be installed on the dashboard with the angled cup or
recessed in the door side with the flush cup.
Recessed mounting:
You need a hole with a diameter of 46 mm / 1,81" in the door side.
Put the two metal wings through the two tracks in the center of the
cup, just as the picture shows, and attach them with the M4 screw
and nut through the center hole. The cup is attached to the door
side when the metal wings is pressed to the back side of the door.
Put the tweeter driver into the cup with the cable going out through
the bottom hole. Then attach the driver into the cup and turn it
clockwise to attach to the cup. When removing the tweeter driver
from the cup, turn it ccw and lift it up.
Angled surface mounting:
For angled surface mount together with the angled cup:
The tweeter driver is attached to the cup by fitting the three wings
on the angled cup into the tracks of the driver and then turn it
clockwise. When removing the driver from the cup, turn it ccw and
lift it up.
