DLS REFERENCE SPEAKERS
OWNERS MANUAL
Welcome
Thank you for buying a DLS speaker. This model is a part of
DLS Reference speaker line.
Install the speakers yourself if you feel confident with our in-
structions and if you have the proper tools. A poor installation
job can destroy the final result even from these speakers, so if
you feel unsure, turn over the installation job to someone better
suited to it.
Installation
Mount the speakers in the door or in the dashboard of your
car. Normally they will fit in the facory pre-made mounting ho-
les. If you want an improved sound reinforce with a baffle of
MDF-board or similar. An installation high up on the door side
is to be prefered.
In many vehicles there are factory made places for tweeters
that you can use for installation. If this is impossible, try to In-
stall the tweeter close to the bass/mid driver. The tweeter can
also be installed on the dash-board, or recessed in the door
with the accessories coming with the tweeters.
It is important to fasten the speakers properly in order to avoid
bad sound or rattling.
Connect the speakers to the crossovers as in this drawing:
Technical Assistance
For technical assistance ask the shop where the product was
sold or the distributor in your country.
You can also send an e-mail to [email protected]
Information can also be found on our web-site www.dls.se
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.
Warranty service
This speaker is covered by warranty, depending on the condi-
tions in the country where it is sold. If the speaker is returned
for service, please include the original dated receipt (or a copy)
with the product.
Installation of tweeter RC28
RC28 can be mounted on the dash-
board with the angled cup (1) cup, or
recessed in a door side.
Surface mounting:
For angled surface mount use the ang-
led cup:
The tweeter driver is attached to
the cup by fitting the three wings on
the angled cup into the tracks of the
tweeter driver and then turn it clock-
wise to lock. When removing the driver
from the cup, turn it ccw and lift it up.
The cable goes through the hole in the
rear side of the cup.
Recessed mounting:
Drill a hole with a diameter of 48
mm / 1,89” in the door side.
The cup (2) is attached to the door
side with the metal wing(3) press-
sed to the back side of the door.
Fasten the metal wing using the
two M3 screws.
Put the tweeter driver (1) into the
cup with the cable going out th-
rough the bottom hole. Then at-
tach the driver into the cup and
turn it clockwise to lock in the cup.
When removing the driver from
the cup, turn it ccw and lift it out.
Technical data RC28 tweeter
DLS Svenska AB
P.O Box 13029
SE-40251 Gothenburg
Tel: +31840060
Fax: +31844021
E-mail: [email protected]
www.dls.se
Size
28 mm / 1,1”
Nom. power handling (RMS) 50 Watt, 80 Watt max
Frequency response
1,5 kHz-25 kHz
Sensitivity
93 dB
Magnet diameter
35 mm / 1,38” neodymium magnet
Mounting depth
20 mm / 0,8” (recessed install)
Mounting hole
48 mm / 1,9” (recessed install)
Cone material
Textile fibre
RC6.2
2-way
system
Technical data bass driver
DLS RC6.2
Impedance
4 ohm
Nom. power RMS
100 W
Max / peak power
150 W / 300 W
Cone material
Black anodized aluminum
Woofer size
6,5”(16,5 cm)
Magnet size
110 mm/4”
Sensitivity
86 dB
Mounting depth
75 mm/2,95”
Mounting hole
145 mm / 5,7”
Connection of crossover RC6.2
Black -
DLS RC6.2 crossover
Connection of one channel, the
other is connected in the same
way.
Red + Black -
Tweeter
Tweeter level:
Hi=High level
Lo= Low level
Select level
with the slide
switch inside
the filter box
+ IN - + WF- +
TW -
Lo
Hi
Head unit /
amplifier
- +
3
2
