DLS PERFORMANCE SPEAKERS
OWNERS MANUAL
Welcome
Thank you for buying a DLS speaker. This model is a part of
DLS Performance speaker line.
Install the speakers yourself if you feel confident with our in-
structions and if you have the proper tools. A poor installation
job can destroy the final result even from these speakers, so if
you feel unsure, turn over the installation job to someone better
suited to it.
Installation
Mount the speakers in the door or in the dashboard of your
car. Normally they will fit in the facory pre-made mounting ho-
les. If you want an improved sound reinforce with a baffle of
MDF-board or similar. An installation high up on the door side
is to be prefered.
In many vehicles there are factory made places for tweeters
that you can use for installation. If this is impossible, try to In-
stall the tweeter close to the bass/mid driver. The tweeter can
also be installed on the dash-board, or recessed in the door
with the accessories coming with the tweeters.
It is important to fasten the speakers properly in order to avoid
bad sound or rattling.
Connect the speakers anf crossovers as in this drawing:
Technical Assistance
For technical assistance ask the shop where the product was
sold or the distributor in your country.
You can also send an e-mail to [email protected]
Information can also be found on our web-site www.dls.se
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.
Warranty service
This speaker is covered by warranty, depending on the condi-
tions in the country where it is sold. If the speaker is returned
for service, please include the original dated receipt (or a copy)
with the product.
Installation of tweeter M25
M25 can be mounted on
the dashboard with the
angled cup (1) cup, or
recessed in a door side.
Surface mounting:
Angled mounting
:
Put the cable through the hole in the rear
end of the angled cup. The tweeter (2) is attached to the cup
by putting them together and turn clockwise. Attach the cup to
the surface with the double adhesive tape.
Recessed mounting:
You need a hole with a diameter
of 43 mm/ 1,7”. Put the two metal
wings (4) through the two tracks
in the center of the cup (3), just
as the picture shows, and attach
them with the M4 screw and nut
through the center hole. The cup
is attached to the door side when
the metal wings is pressed to the
back side of the door.
Put the tweeter driver into the cup
with the cable going out through
the bottom hole. The tweeter (2)
is attached to the cup by putting
the tweeter into the cup and turn
clockwise.
Technical data M25 tweeter
DLS Svenska AB
P.O Box 13029
SE-40251 Gothenburg
Tel: +31840060
Fax: +31844021
E-mail: [email protected]
www.dls.se
Size
25 mm / 1”
Nom. power handling (RMS) 50 Watt, 80 Watt max
Frequency response
1,5 kHz-20 kHz
Sensitivity
93 dB
Magnet diameter
30 mm / 1,18” neodymium magnet
Mounting depth
20 mm / 0,8” (recessed install)
Mounting hole
46 mm / 1,81” (recessed install)
Cone material
Textile fibre
Red + Black -
Crossover box
Connection of one channel,
the other is connected in the
same way.
The tweeter level can be ad-
justed by connecting / discon-
necting the transparent cable
coming from the filter box.
Black -
Head unit /
amplifier
Connection of crossover M6.2
Tweeter M25
Black - Blue +
DLS M6.2
crossover
M6.2
2-way
system
4
3
Technical data bass driver
DLS M6.2
Impedance
4 ohm
Nom. power RMS
60 W
Max / peak power
80 W / 160 W
Cone material
Paper cone with textile fibres
Woofer size
6,5”(16,5 cm)
Magnet size
90 mm/3,54”
Sensitivity
89 dB
Mounting depth
65 mm/2,56”
Mounting hole
145 mm / 5,7”
Tweeter level:
ow level: Connect the cables
High level: Disconnect
Transparent cable
1
2
