background image

How to install and operate

the

DLS CAD11

&

DLS CAD15

digital mono amplifiers

Welcome!

This owners manual is written in easy english and
uses a lot of drawings to simply the installation and
use of the above amplifier.

Your DLS amplifier must be installed correctly in or-
der to work well. This manual will show you how to
install the amplifier like a pro. Please read the entire
manual before beginning the  installation.
Install the amplifier yourself if you feel confident  with
our instructions and if you have the proper tools.
However if you feel unsure, turn over the installa-
tion job to someone better suited to it.

Warranty Service

This amplifier  is covered by warranty, depending
on the conditions in the country where it is sold. If
the amplifier is returned for service, please include
the original dated receipt with the product.

 

 

 

 

 

 

Technical Assistance

For technical assistance ask the shop where the
product was sold or the distributor in your very coun-
try.
You can always phone the DLS Helpdesk in Sweden
+ 46 31 84 00 60 or send an e-mail to [email protected].
Information can also be found on our WEB-site
www.dls.se

Contents

Specifications................................

1

Features……………………………..

2

Installation…………………….…….

2

Tools and materials needed……….

3

Amplifier installation kit…………....

3

Routing Wires……………………....

3

Wiring

Power and Outputs……………..….

4

Inputs and controls………………...

5

Input level control..........................

5

Crossovers…………......................

5

Phase control.....………………...…

5

Bass boost control.........................

6

Remote bass level control.............

6

Speaker wiring:

Single amplifier system………….….

6

Testing.............................................

6

Bridging two CAD11.........................

7

Bridging two CAD15........................

8

Subwoofer connections……………..

9

Professional tips...............................

10

Technical data..................................

11

Trouble shooting..............................

11

DLS Svenska AB

P.O. Box 13029

S-40251 Göteborg, Sweden

Tel: +46 31 840060

Fax: +46 31 844021

E-mail: [email protected]

www.dls.se

DLS Svenska  

AB -  2007-01-10

We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.

Approval of electromagnetic compatability according
to the EEC Directive 95/54/EC

 E 13

   CAD15 approval No: 022944

   CAD11 approval No: 022495

Summary of Contents for DLS CAD11













Reviews: