background image

 

DLI 8300 PRODUCT MANUAL 

PAGE 48/50 

Rev. 4 

 
 
 
 
For further information, please contact: 

 

Data Ltd. Inc. 
703 Data Ltd Parkway 
P.O. Box 761 
La Porte, IN 46352 USA 
(800) 526-1299 

 

Data Ltd. Inc. shall not be liable for use of our product with equipment (i.e., power supplies, 
personal computers, etc.) that is not CE marked and does not comply with the Low Voltage 
Directive 
 
 

 

FCC Compliance 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation. 

 

This equipment has been tested and found to comply with the limits for a Class B digital device 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 
If necessary, the user should consult the dealer or an experienced radio/television technician for 
additional suggestions. The user may find the following booklet he

lpful: “Something About 

Interfere

nce.” This is available at FCC local regional offices. Our company is not responsible for 

any radio or television interference caused by unauthorized modifications of this equipment or the 
substitution or attachment of connecting cables and equipment other than those specified by our 
company. The correction is the responsibility of the user. Use only shielded data cables with this 
system. In accordance with FCC 15.21, changes or modifications not expressly approved by the 
party responsible for compliance could void the user

’s authority to operate the equipment. 

 

This device and its antenna must not be co-located or operating in conjunction 
with any other antenna or transmitter. To maintain compliance with FCC RF 
exposure guidelines for body-worn operation, do not use accessories that

 

contain metallic components.

 

 

When using accessories where the terminal is worn on the body, the terminal

’s touch screen 

must face away from the body. 

CAUTION! 

Any changes or modifications not expressly approved by the grantee of this 

device could void the user's authority to operate the equipment

 

Summary of Contents for 8300



















































Reviews: