manualshive.com logo in svg

DLE JETBOARD, User Manual, Page: 38 / 39

Share
Download
DLE JETBOARD User Manual Download Page 38

35

9

、

After-sale Service

If you have any questions about our product, please do not hesitate to contact your local distributor or us directly. Please provide your

name, address, contact phone number and detailed problem description, recommendations or compliments to us. We will provide you the best -

quality service.

Please call our customer-service line (400-100-6090

）

. Or send your request to our email: [email protected]. Please visit our website:

www.dlengine.com for latest news and information.

Warranty policy

1.We provide 1 year warranty from date of purchase.

2.Spark plug, starter motor and other consumables are not covered under warranty.

3.Warranty will be void if the board is modified, none-original parts are used and for unwarrantable damages.

4.Engine damage from using a wrong mixing ratio or low quality lubricant will void the Warranty.

5.Engine/parts damaged because of violent operation or the impeller ingesting foreign matter during use will void the Warranty.

6.Please keep the warranty card and in case of a warranty request send it with the returned parts, for warranty recording.

If there is any mistake or omission in the manual ,please contact us, thank you.

Summary of Contents for JETBOARD








































Reviews:

No comments