Anti-Grounding Plate
TIME
DELA
Y
EXIT
LOOP
LM
T
REVERS
E
LOOP
REV SENSE
OPEN
REV SENSE
CLOS
E
1
ON
23
4
1
ON
23
45
67
8
NC
NO
P8
P7
P6
4404-010
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
9410
9410
1 2 5 6 11 13A 13B 13E 25
16
17
U
L1 L2/N
B- B+
V
W PE PE
Mode
EPM
1.0
PE
SCM series
basic I/O control
115 VAC Convenience Outlets
DO NOT
power up and
cycle the operator until
the “DIP-Switches” and
the “Limit Switches”
have been adjusted.
Damage could occur to
the gate and operator.
T
T
T
T
T
T
T
T
T
Opening
direction
OFF setting.
Opening
direction
ON setting.
Tip: It is recommended that a surge suppressor be installed on the high voltage
power lines.
GATE OPERATOR MUST BE PROPERLY GROUNDED!!
CAUTION
High Voltage AC input power MUST MATCH
the operator specifications or DAMAGE will
occur and VOID the warranty!
VERIFY Input AC power MATCHES your
specific operator power BEFORE wiring!
EXIT
LOOP
LM
T
REVERS
E
LOOP
REV SENS
E
CLOS
E
P8
P7
P6
440
4-01
0
1
2
4
3
1
2
4
3
1
2
4
3
Ele
ct
ro
ni
c Bo
x
Power safety and opening devices
that require 115 VAC power.
Two 115 VAC Convenience Outlets
Model 9200 is intended for installation only on sliding gates used for vehicles.
Pedestrians must be supplied with a separate access opening. For safety and installation instructions,
please refer to the Installation/Owner’s manual.
See reverse side
See reverse side to wire main terminal.
With power OFF, push and hold the
lock plate down where shown to
adjust the Open and Close limit nuts.
After adjusting the limit-nuts, be sure
that the lock-plate is engaged in the
slots on the limit-nuts to prevent them
from rotating.
The slow-down limits on all models
but the 9210 will move up or down
3/4 inch.
DO NOT
remove the
slow-down limit assembly from the
3/4 inch slot and re-attach it in the
longer slot on the partial open
adjustment rail to gain further
adjustment.
This will cause mechani-
cal damage to the switch assembly
when the operator is activated.
Turn power ON and activate the gate
operator. Re-adjust the limit nuts as
necessary for full-open and full-close
gate travel. After you are satisfied with
the gate limit settings, the speed
control knob can then be adjusted on
all models but the 9210 to personal
preference.
4”
Min.
Pad depth is determined by soil conditions and local building codes.
Minimum depth is 18 inches. Reinforced concrete recommended.
Concrete Pad
Wire
Mesh
3/4”conduit with
sweeps recommended.
Clear Plastic Electronic Box Cover
1
2
3
QUICKSTART “BASIC” GUIDELINES FOR MODEL 9200 “FULL OPEN”: MOUNTED ON THE PEDESTAL MOUNTING STAND
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
Copyright 2013 DoorKing, Inc. All rights reserved.
9240-066-E-2-13
Plug-In Loop Detectors
Not included - Refer to the Installation/Owner’s manual AND
Loop Information Manual (available from
www.dkaccess.com
)
for more information on loops and plug-in loop detectors.
Important Note:
DoorKing highly recommends that loops and
loop detectors are installed with this slide gate operator. A loop
detection system will preventing the gate from automatically
opening or closing on a vehicle when it is in the gate’s path.
High Voltage Connection
DIP-Switches
Limit Switches
1. Opening Direction
2.
ON
3.
ON
4. OFF
5. OFF
6. OFF
7. OFF
8. OFF
1. OFF
2. OFF
3. OFF
4. OFF
Auto-Close Timer
Chassis
Ground
DANGER
HIGH VOLTAGE!
1
ON
23
45
67
8
1
ON
23
4
SW 1 and 2 are Upside-Down on Circuit Board.
1
23
TIME
DELA
Y
A
B
D
C
C
C
B
D
1 ft/s
.5 ft/s
0 ft/s
2 ft/s
1.5 ft/s
Limit LEDs
Plug-In Loop
Detector
Plug-In Loop
Detector
Min Max
Speed
Push
Pu
sh
Lock
-Plat
e
Limit Nu
t
Limit Nu
t
1
2
1
2222
Slow
-D
own
Li
m
it
Slow-Down
Limi
t
1A
2A
Par
tial Open
Not Used
1
2
2A
1A
Adjust 1 to 23 sec.
1 Limi
t
Switch
2 Limi
t
Switch
Check polarity of Three Phase:
Position the gate half way open.
Give open command and while
gate is opening, activate the
appropriate limit switch with your
finger. Gate should STOP. If it does
not, activate the other limit switch.
If this STOPS the gate, AC power
wires must be changed (Reverse
the connection of any 2 wires and
re-check limits).
Pa
rtia
l Op
en
A
dju
stme
nt
Ra
il
208/230 VAC
THREE Phase
Chassis
Ground
High
Voltage
AC Input
Wire
Hot
115 VAC Output
Hot
Hot
208/230 VAC
SINGLE Phase
Chassis
Ground
High
Voltage
AC Input
Wire
Hot
115 VAC Output
Hot
Hot
Use only two legs
of the incoming
3-phase power.
Chassis
Ground
High
Voltage
AC Input
Wire
Hot
115 VAC Output
Neu
115 VAC
SINGLE Phase
White - Neutral
Black - 115 VAC Hot
Green - Chassis
Ground
SW 1
SW 2
A
A
A
Operator MUST be parallel to gate!
Chain brackets MUST
align with idler
wheels so chain
stays parallel to gate!
Remove the 3 locknuts inside the
electronic box to swing box open.
Gain Access Inside Operator
Move the idler wheels to the lower position.
Fits on All 9200 Models.
Standard with 9230, 9235, 9240 and 9245 Models
1/2
Attach pedestal stand with
sixteen (16) 1/2” x 3” sleeve
anchors (not supplied) after
concrete pad has been
poured and has cured.
Bolt operator to
pedestal with
hardware supplied
in pedestal kit.
Manual
crank in
store
d
position.
Caution:
Never
attempt to
manually
operate the
9200 until
you have
verified that
power has
been shut-off.
Connect
Chain to
the Gate
Chain nut
and chain bolt
should not protrude
past gate frame. The chain
should sag no more than one
(1) inch per 10 feet of travel. Do not
over tighten the chain.
Chain
Nut
Chain Bolt
Option
2
Master Link
Option
1
Gate
Frame
1”
Assemble Pedestal
Mounting Stand
Concrete Pad
Dimensions,
Pedestal
Mounting
Stand and
Conduit
Positions
1.75”
11.75”
4”
6.25”
4”
4”
Concrete Pad
Conduit
Area
Concrete pad
MUST be level!
Idler
Wheels
Gate
Chain
Bracket
Conduit
Chain
Bracket
Chain
Bracket
Idler Wheels
Chain
Configuration
Concrete Pad
Elect
ronic Bo
x
DoorKing
Part Number
9200-13
5
See instruction
sheet with
pedestal kit
for assembly.
Chain
Tray
Washer
12 Sets
Washer
Lockwasher
Operator Base Plate
Gate
“Optional” Chain
Tray Kit:
Recommended for
gates longer than 20
ft. to support the
weight of the chain.
DoorKing offers a
chain tray and
supporting brackets
in 10 ft. sections to
fit any length gate
(DoorKing Part
Number 2601-270,
10 Ft. section). See
instruction sheet
with chain tray kit
for installation.
Chain brackets MUST
be mounted so the
chain remains the
same height as it is
on the idler wheels!
15.75”
11.75”
11.75”
10.5”
10.5”
10.5”
10.5”
1”
39.25”
22”
Top
Views
Side
Views
Pedestal mounting stand
MUST be level!
Idler
Wheel
s
Speed Control Knob
On all models but 9210.
