background image

23

© 2016 Directed. All rights reserved.

Note

The temperature and battery thresholds can be changed by 
an authorized Directed dealer if a higher or lower threshold 
is desired.

Pit Stop Mode

To exit vehicle with engine running.

The system keeps the engine running during short trips into the house 
or convenience store. To perform Pit Stop:
1.  With the engine running, 

set

 the parking brake and 

release

 the 

foot brake.

2. 

Press

 the 

AUX

AUX

 button, the  parking lights will turn on to indicate 

remote start is on. 

3. 

Turn 

the key to OFF, and

 remove 

it from the ignition, the engine  

continues running for the programmed runtime. 

4. 

Exit

 the vehicle and 

arm

 the alarm.

Note

For Pit Stop Mode on manual transmission vehicles follow 
the directions in the 

MTS Mode 

(

Manual Transmission Start)

 

section with the door open.

MTS Mode (Manual Transmission Start)

When installed into a manual transmission vehicle, the system requires 
that the MTS Mode is properly set when parking. If MTS Mode is not 
properly set or is defeated after being properly set the system will not 
start the engine.

1.  With the engine running, 

place

 gear shifter in neutral position, 

press

 the foot brake, then 

set

 the parking brake and leave the 

engine running. 

Summary of Contents for Clifford 5606X











































Reviews: