background image

1122

© 2004 Directed Electronics, Inc 

ESP FEATURES AND CONTROLS

The ability to access the feature settings
of your amplifier is only possible with
the use of a Directed Electronics
Bitwriter

®

unit. Firmware version 1.8 or

later is required in the Bitwriter

®

.

Versions prior to 1.8 will not program
the amplifier.

MAIN FEATURES

1. TTuurrnn--oonn  ddeellaayy  -- 0.75, 1.00, 1.25,

1.75, 2.25, 2.75, or 3.25 seconds
is selectable. 22..7755 seconds is the
factory default setting.

2. AAnnttii--tthheefftt  -- On/Off/Reset Anti-Theft

Trigger. Selecting ON places the unit
in the alarm monitoring (amplifier
disable on loss of 12V) condition.
Off disables alarm monitoring.
Reset Anti-Theft Trigger allows the
amplifier to be unlocked from the
loss of 12V. OOffff is the factory
default setting.

To unlock the amplifier, use the
following procedure:

AA.. Plug the Bitwriter

® 

into one of

the ESP ports and turn the
Bitwriter

® 

ON.

BB.. Select AAnnttii--TThheefftt from the menu.

ii.. Select  AAnnttii--TThheefftt RReesseett from
the submenu.

iiii.. Press W

Wrriittee twice.

CC.. Select AAnnttii--TThheefftt from the menu
again.

ii.. Select OOffff from the submenu.

iiii.. Press W

Wrriittee twice.

“W

Wrriittiinngg   SSuucccceessssffuull” message

will appear on the Bitwriter

®

display if the procedure was
successful.

3. VVaalleett  m

moonniittoorriinngg  -- Enable/Disabled

DDiissaabblleedd is the factory default
setting. The amplifier will not power
up if the alarm system is in Valet.

4. IInnppuutt   ggaaiinn   aaddjjuussttm

meenntt   -- UUnnlloocckk is

the factory default setting.
Lock/Unlock, in the lock position
the gain adjustment located on the
top panel is software locked at the
input gain range that is selected.

5. IInnppuutt   ggaaiinn   rraannggee   -- 0.25–0.50,

0.50–1.25, 1.25–3.00, or
3.00–6.00 V, and 00..2200–

–88..0000VV

(factory default). This limits the
gain adjustment to the specified
range.

6. FFaann  CCoonnttrrooll  -- On/Auto/Off

This controls an external fan
connected to the fan port.

Summary of Contents for 1200T



















Reviews: