2.0
F
EATURES
This high-performance DirectConnect
®
High Speed HDMI™ CAT5/6 Extender
via
dual
(2)
CAT5e or CAT6 with cross stand inside UTP cable has many benefits and
features that enable it to perform in a superior manner. Among those benefits and
features you will find:
2 sets of HDMI™ inputs at transmitter, application could be 2 HDMI™ inputs
and 2 HDMI™ outputs when using additional
(optional)
receiver SKU# .15698
HDMI™ cable length is fixed and unchangeable after it is produced. HDMI™
connectors can only be soldered or terminated by the professional
manufactures that produce them, the installer and/or users cannot modify by
themselves. However Cat5 or Cat6 UTP cables are available everywhere and
be processed easily.
HDMI™ cables are not easy to bend and the connectors are large to pull
through conduit and the wall. However, Cat5/6 cable has no such problems.
Uses Cat5 or Cat6 UTP cable
to substitute for HDMI™ cable to achieve
long distance transmission without signal loss.
Equalization boost via DIP switch on back side of each receiver to adjust
variables to compensate for the length of the link cable
(< 25 meters or > 25meters)
.
HDMI™ 1.3 and HDCP 1.1 compliant up to full 1080P and supports DDC & EDID
Dual
(2)
Cat5 or Cat6 UTP cables can substitute a HDMI™ cable to achieve long
distance transmission of 148 feet
(Cat5)
or 164 feet
(Cat6)
@ 1080P.
Supports DVI equipment with the use of a
HDMI™ to DVI adapter. It provides an
easy and flexible cabling solution for integrating home theater components.
3.0
P
ACKAGE
C
ONTENTS
Before attempting to use this DirectConnect® unit, please check the packaging and
make sure the following items are contained in the shipping carton:
DirectConnect
®
HDMI™ Extender One
(1)
Transmitter and one
(1)
Receiver
Two (2) 5 Volt DC Power Adapters
User's Manual
Note:
Please retain the original packing material in case you need to return the unit. If you
find any items missing, contact DirectConnect
®
immediately (800.531.3224). Please have
the model number, serial number, and invoice available for reference when you call.
.
4.0
C
ONNECTION AND
O
PERATION
1) Connect the HDMI™ signal source to the transmitter unit input port
(HDMI™ IN)
* Please refer to connection diagram section
(Page 5)
.
2 & 3) Connect dual Cat5 or dual Cat6 UTP cable between the transmitter and receiver
units. Please use EIA/TIA-568 termination
(T568B)
.
4) Connect the HDMI™ display device to the receiver unit output port
(HDMI™ OUT)
5) Insert the DC side of the 5v power supply into the transmitter and
receiver before connecting to
the wall outlet. Then connect the AC side of the power supply into the wall outlet after all
connections have been made.
(Ideally the AC power should be surge suppressed and filtered)
.
Attention:
Insert/Remove cables gently
& avoid twisting/kinking your HDMI™ cables.
4.1
P
ANEL
D
ESCRIPTIONS
HDMI™ Extender Transmitter
1 - HDMI™ Input
2 - Cat5 Output – Video
5 - DC Input Power
3 - Cat5 Output – Data
HDMI™ Extender Receiver
4 - HDMI™ Output 2 - Cat5 Output – Video 5 - DC Input Power
3 - Cat5 Output - Data
Please use EIA/TIA-568 termination (T568B) and do not apply DC power to unit until all connections are made.
4.2
C
ONNECTION
D
IAGRAM
Note: In order to achieve the highest transmission quality, please choose unshielded Cat5e or Cat6 and terminate with metal
RJ-45 connectors
.
Higher-resolutions and longer transmission distances require low skew cables for the best performance.
1. The cables with lower quality will not achieve the perfect transmission effect and long distance.
2. Theoretically the function of this product is normal when adopting short distance transmission.
If this product cannot transmit long distance, there may be quality problems in the transmission cables.
4 / 8
5 / 8
OPTIONAL RECEIVER
A
- DIP SWITCH SETTING: (back side)
================================
１
(Input Equalization Boost Setting)
↑
ON (Cable Length > 25M)
↓
OFF (Cable Length < 25M)
Recommended
「
ON
↑」
--------------------------------------------------------
-