manualshive.com logo in svg

Dini Argeo 3590E Series, User Manual

Share
Download
Dini Argeo 3590E Series User Manual Download Page 47

3590EXTLWBCIO, CPWELW series indicator 

E-LW_01_14.03_EN_U 

 

 

46 

15.4.4 DOSAGE 

By selecting this functioning mode the output is enabled when the dosage is started and it is disabled when the dosage 
ends (see section 13.1). 
 

15.4.5 DOSAGE TARGET 

By selecting this functioning mode the output is enabled when the totalised weight reaches the value set for the dosage end 
by weight, therefore after the dosage end. The output is disabled by manually disabling the cycle. 
 

15.4.6 PAUSE 

By selecting this functioning mode the output is enabled when the dosage is paused, and it is disabled when the dosage 
restarts. 
 

15.4.7 MAX.FL.R AND MIN.FL.R 

By selecting on of this functioning modes, the output is enabled when the flow is respectively greater than the  
the value set in the 

<<F.R.ERR.>>

 step

 

or

 

less than the TARGET - the value set in the 

<<F.R.ERR.>>

 step. 

 

15.4.8 ALARM 

By selecting this functioning mode the output is enabled when a generic alarm is activate.

 

 

15.4.9 LOCK 

By selecting this functioning mode the output is enabled when time set in the FILL LOCK TIME step  

<<LOK.TIM>>

.

 

 

15.4.10 WEIGHT PULSE 

By selecting this functioning mode the output is enabled when is reached a weight value set in the setup).

 

 

15.4.11 FILLING ENABLED 

By selecting this functioning mode the output is enabled when the system is in the filling status.

 

 

15.4.12 MATERIAL ENABLED 

Enabling of the relay: 
-  on the active dosage; 
Disabling of the relay: 
-  In the dosage by a weight it disabled the relay at TARGET WEIGHT – FLY WEIGHT. 

-  In the dosage by a time, it disabled the relay at the time set for the dosage. 
Manually ending the dosage, through the START/STOP input of the dosage. 

 

15.4.13 LOW FLOW RATE 

By selecting this functioning mode the output is enabled when the flow rate is lower than the set value ( in article database). 

Summary of Contents for 3590E Series


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands