Dinel PDU-40-W Series, User Manual

Page: 49 / 56

User manual - METER PDU-4x0-W
Register Write Range Register description
16h Yes 0 ÷ 999 “ Lo r ” parameter in “ InPt ” menu, in 0.1%
17h Yes 0 ÷ 199
“
Hi r
” parameter in “
InPt
” menu, in 0.1%
18h Yes 0 ÷ 9999 “ t h1 ” parameter in “ InPt ” menu, no decimal point included
19h Yes 0 ÷ 9999 “ t h2 ” parameter in “ InPt ” menu, no decimal point included
1Ah Yes 0 ÷ 9999
“ t h3 ” parameter in “ InPt ” menu, no decimal point included
1Bh Yes 0 ÷ 9999 “ t d ” parameter in “ InPt ” menu, no decimal point included
1Ch Yes 0 ÷ 9999 “ t Sn ” parameter in “ InPt ” menu, no decimal point included
1Dh Yes 0 ÷ 9999
“ t Sh ” parameter in “ InPt ” menu, no decimal point included
20h 2 Yes 0 ÷ 199 Device address
21h No 21F0h Device identification code (ID)
22h 3 Yes 0 ÷ 7
“bAud” parameter in “rS” menu (baud rate);
0 - 1200 baud; 1 - 2400 baud; 2 - 4800 baud; 3 - 9600 baud;
4 - 19200 baud; 5 - 38400 baud; 6 - 57600 baud; 7 - 115200 baud
23h 4 Yes 0 ÷ 1
“mbAc” parameter in “rS” menu (permission to write registers via
RS-485 interface); 0 - write denied ; 1 - write allowed
24h Yes see descr.
Parameters of “
SECU
” menu (binary format (0 - „
oFF
”, 1 - „
on
”):
bit 0
- “
A r1
” parameter;
bit 1
- “
A r2
” parameter
25h Yes 0 ÷ 5
“rESP” parameter in “rS” menu (additional response delay);
0 - no additional delay; 1 - ” 10c ” option; 2 - ” 20c ” option;
3 - ” 50c ” option; 4 - ” 100c ” option; 5 - ” 200c ” option;
27h Yes 0 ÷ 99
“mbtO” parameter in “rS” menu (maximum delay between
received frames); 0 - no delay checking;
1 ÷ 99 - maximum delay expressed in seconds
2Dh Yes 1 ÷ 8
“ bri ” parameter (display brightness);
1 - the lowest brightness; 8 - the highest brightness
2Fh Yes 0 ÷ 1
“ Edit ” parameter (numerical parameters edit mode);
0 - „ dig ” mode; 1 - „ SLid ” mode
30h Yes -999 ÷ 9999 “ SEtP ” parameter in “ rEL1 ” menu, no decimal point included
31h Yes -999 ÷ 999
“ HySt ” parameter in “ rEL1 ” menu, no decimal point included
32h Yes 0 ÷ 5
“ modE ” parameter in “ rEL1 ” menu:
0 - “ noAC ” mode; 1 - “ on ” mode; 2 - “ oFF ” mode; 3 - “ in ” mode;
4 - “ out ” mode; 5 - “ modb ” mode
33h Yes 0 ÷ 999
“t on”
parameter in
“rEL1”
menu, expressed in tenth of seconds or
tenth of minutes depend on
“unit”
parameter - register no. 35h)
34h Yes 0 ÷ 999
“toFF” parameter in “rEL1” menu, expressed in tenth of seconds
or tenth of minutes depend on “unit” parameter - register no. 35h)
35h Yes 0 ÷ 1
“unit” parameter in “rEL1” menu:
0 - seconds; 1 - minutes
36h Yes 0 ÷ 2
“AL” parameter in “rEL1” menu: 0 - no changes; 1 - on; 2 - off
49