Dimplex Toluca Deluxe, Manual

Page: 4 / 8

Operating Instructions:
Please see Fig. 3
Icon Display Funtion Description
A -
Power /
Standby
Press Once to turn the product ‘ON’.
Press a second time to put the product into ‘STANDBY’
(When returning from ‘STANDBY’ mode the product will return to previous settings unless
the product has been unplugged, in which case it will reset to factory settings)
B
‘FLAME EFFECT’ button this turns the flame effect ON or OFF independently of the
products other features.
+
Flame
Up
This Button will increase the brightness of the flame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY increase the brightness level.
-
Flame
Down
This Button will decrease the brightness of the flame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY decrease the brightness level.
fC
Flame
Cycling
This setting is set by pressing the Flame Up button once more after F5. this will cause the
brightness of the flame effect to cycle from F2 to F5 in a continuous Loop.
-
Off
This will turn the flame effect off. If the heater is ON, the display will activate and remain
active to read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/
COOL BLOW.
C
‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the display see Fig.1.
When the flame effect is ‘ON’ the display will turn off after 5 seconds, however if the
heater is being used independently of the flame effect. The low heat or high heat icon
will appear continuously in the display.
Low
Heat
This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW HEAT’
icon. To Adjust the temperature setting the Temp Down or Temp Up buttons described
below must be used.
(This icon is Orange in Colour)
High
Heat
This icon in the display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH
HEAT’ icon. To Adjust the temperature setting the Temp Down or Temp Up buttons
described below must be used.
(This icon is Red in Colour)
Cool
Blow
This icon in the display indicates ‘COOL BLOW’ this setting will be indicated by the ‘COOL
BLOW’ icon and the letters ‘CB’ appearing in the display.
(This icon is Blue in Colour)
- Off
This switches the heater and blower ‘OFF’, no icon will be displayed in the display. Note
the blower will run for 5-10 seconds after being turned off, this is to ensure the product
cools down safely.
D -
Back
Light
Pressing this button will turn ON and OFF the Back Lighting. There are 4 settings, Sides
only, Top only, all OFF and All ON
E -
Temp
Down
Press multiple times to lower the heater temperature in 1
0
C increments. The lowest
temperature that can be set is 18
0
C.
E -
Temp
Up
Press multiple times to increase the heater temperature in 1
0
C increments. The highest
temperature that can be set 30
0
C.
When High Heat is selected, the letters ‘HH’ appear in the display, this means the heat
will remain ON continusously and is not controlled by the thermostat.
F
Sleep
Timer
Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5
hr to 8.0 hr before turning off. The remaining time on the ‘SLEEP TIMER’ displays.
(This icon is Green in Colour)
G
-
Volume
down
Pressing multiple times to control the volume level of the speaker down to mute.
When Bluetooth is not connected, the speaker will play sound of a fire, this can be
turned OFF by pressing this button until the sound is muted.
G
-
Volume
Up
Controls the level of the speaker Volume up.
The volume buttons can also control the volume of your paired bluetooth device
H -
Blue-
tooth
When a device is paired to the product, pressing this button will disconnect the paired
device.
I -
LED
COLOUR
Press multiple times to change the colour of the LED mood lighting and the coloured
fuel bed. The colour can be set as Orange, Red, Green, Blue, or cycling through all four
colours continuously.