manualshive.com logo in svg

Dimplex SUTP Mid Range, Installation Manual

Share
Download
Dimplex SUTP Mid Range Installation Manual Download Page 2

 
 
 

Important -This Manual Should Be Left With The Unit After Installation 

 

 
 
 
 
Table of Contents 

 

1. Introduction.......................................................................................................................................2 
2. Component Check List .....................................................................................................................3 
3. General requirements ........................................................................................................................3 
4. Plumbing Installation ........................................................................................................................5 
7. Electrical installation.........................................................................................................................9 
8. Filling and commissioning- ............................................................................................................10 
9. Servicing and maintenance. ............................................................................................................11 
10. Fault finding..................................................................................................................................12 
11. Users instructions..........................................................................................................................13 
12. Warranty........................................................................................................................................13 
13. Installation, Commissioning and Service Record .........................................................................14 

 
 

 

 

 
 
 

1. Introduction 

 

The

 “SUTP Mid Range”

 is a high quality unvented stainless steel domestic hot water cylinder 

suitable for domestic hot water systems where the cold mains water supply is between 3bar and 12bar. 
Reduced performance is available at lower pressures but the units are not suitable for pressures lower 
than 1.5bar and flow rate of 20 litres per minute. The unit comes complete with all the necessary safety 
equipment to comply with legislation governing the installation of such systems.  
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

2

Summary of Contents for SUTP Mid Range















Reviews:

No comments

Brands by name

Popular brands

Load more brands