Dimplex MULTIFIRE DF3015 Parts And Service Manual Download Page 4

 

3

CAUTION 
If you need to continuously reset the heater, unplug the unit and call Dimplex North America 
Limited at 1-800-668-6663 and press 4 for technical support.  Please have your model and 
serial number ready when calling.

 

 

REMOTE CONTROL 

The remote control has a range of approximately 50 ft. (15.25m), it does not have to be 
pointed at the fireplace and can pass through most obstacles (including walls).  It is supplied 
with 243 independent frequencies to prevent interference with other units. 

 

BATTERY INSTALLATION 

1.  Depress tab on the battery cover on the back of the remote transmitter and remove 

battery cover. 

2.  Install 2 AAA batteries into the remote control.  (included) 
3.  Ensure child lock is in the “unlocked” position. 
4.  Replace the battery cover. 

 
 
 
 

 
 
 

 
 
 
 
NOTE 
When the “BAT symbol is present on the remote control it is recommended to replace the 
batteries promptly, to maintain full functionality of the remote/fireplace. The remote transmitter 
has a battery backup time of only several hours. 
 
INITIALIZING THE REMOTE CONTROL 

1.  Plug cord into 120 volt wall outlet. 
2.  Ensure the Main On/Off switch located in the switch box on the fireplace in the lower 

right hand corner is in the       ON position. 

3.  Set the 3 position manual control to the Remote position (right position). 
4.  Press and hold the initialization button on the unit. 
5.  While holding the initialization button, press the flame/heat ON/OFF       button or the 

Purifire™ ON/OFF       button on the remote control transmitter.   

6.  Release the initialization button on the unit. 
7.  Press the Flame/Heat On/Off button     to turn the Flame/Heat function ON or press the 

Purifire™ On/Off button      to turn the Purifire™ function ON.   

 
 
FREQUENCY INTERFERENCE
 
If the fireplace does not respond properly to the remote control, the remote operating 
frequency may have to be reset.  The remote control can send another frequency code to the 
circuit board to eliminate interference. 

1.  Simultaneously press the “SLEEP TIMER DOWN” button and the “PURIFIRE LOW 

SPEED” button on the remote control. 

Batteries 

FIGURE 3 

 

Summary of Contents for MULTIFIRE DF3015

















Reviews: