Using the heater
The mains neon (see
Fig. 1
) will light up to show that the heater
is connected to the mains supply.
Heat control
- see
Fig. 2
The heat control positions are as follows:
O
-
Off
-
Cool Blow *
I
-
Half heat output
II
-
Full heat output
Fig.2
Thermostat control
- see
Fig. 3
The heat output is controlled by the thermostat, according to the
room temperature. Turn the knob to maximum setting initially.
When the room is warm enough, reduce the setting slowly until
the heater just clicks off.
The heater will now cycle on and off to maintain your selected
room temperature.
Fig. 3
NOTE: If the heater does not come on when the thermostat is
set to a low number, this is normally because the room is
warmer than the thermostat setting and is not a fault.
* When the heat control is set to
‘
’ for Cool Blow, set the
thermostat control to max. position.
Position
‘
’
will turn the heater on and off to maintain a
temperature of approximately 5°C to help protect against frosty
conditions.
Safety
– Overheat Protection
For your safety, this appliance is fitted with a thermal cut-out. In
the event that the product overheats, the cut-out switches the
heater off automatically.
To bring the heater back into operation, remove the cause of
the overheating, then unplug or turn off the electrical supply to
the heater for a few minutes.
When the heater has cooled sufficiently, re-connect and switch
on the heater.
Cleaning
ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE UNDERTAKING ANY CLEANING OPERATION.
TO ENSURE CONTINUED NORMAL OPERATION OF YOUR
HEATER, YOU MUST REGULARLY CLEAN OUT ANY
ACCUMULATION OF PARTICLES FROM INSIDE THE HEATER!
THIS IS BEST ACHIEVED BY USING YOUR VACUUM CLEANER
IN BLOW MODE TO BLOW AIR INTO THE HEATER THROUGH
THE FRONT AIR OUTLET TO DISLODGE ANY ACUMULATED
MATTER FROM THE BACK OF THE ELEMENT (IF IT DOES NOT
HAVE THIS FUNCTION, THEN BLOWING HARD YOURSELF
WILL HAVE THE SAME RESULT). THEN USE THE VACUUM IN
SUCTION MODE TO SUCK OUT THE NOW LOOSE PARTICLES
THROUGH THE TOP AND BOTTOM AIR INLETS. THIS WILL
SERVE TO CLEAN THESE AREAS ALSO.
For normal surface cleaning, do not use detergents, abrasive
cleaning agents or polish of any kind on the heater. Wipe with
a dry cloth to remove dust and a damp (not wet) cloth to clean
off stains. Be careful not to allow moisture into the heater
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it should
not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.
After Sales Service
Your product is guaranteed for three years from the date of
purchase. Within this gurantee period, we undertake to repair or
exchange this product free of charge (subject to availability).
PLEASE NOTE - This guarantee will be void if the product
is not used and maintained according to the details and
warnings contained in these user instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales information or assistance with
this product please go to where you will find our self help guide
by clicking on
“After Sales” or ring our helpdesk on 0845 600
5111 (UK) or 01 842 4833 (R.O.I.) .
Spare parts are also available on the website
Please retain your receipt as proof of purchase.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and
EN60555-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
Dimplex UK Ltd.
Millbrook House
Grange Drive
Hedge End
Republic of Ireland Tel.
01 8424833
Southampton
Hampshire. SO30 2DF
[c] Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex UK Limited.
