Soffit or Stair Riser Installation
1. Cut opening as for kickspace installation (22 3/8” x
3 5/8”). Allow 3/4” clearance above cabinet doors.
Add supports for unit (Fig.3).
2. Proceed as for kickspace installation. After
securing unit in opening, install combination of
frame and grille (fig.1).
CAUTION - Disconnect main to de-energize receptacle
before servicing or for electrical inspection.
SERVICING - Remove grille and frame by removing
screws “A”. Remove two screws “B”, and slide out heating assembly. When re-assembling, reverse the
procedure above.
Cleaning
With grille in place - Use vacuum cleaner hose to suck out lint and dirt around grille. Reverse hose on vacuum to
use as a blower to move dust out of enclosure. Reverse hose back to suck out dirt at front area of heater.
With grille removed - Remove two screws “B” at bottom front of heating element assembly. Pull gently to remove
it from enclosure. Swing assembly out. Vacuum inside of enclosure and around heating element assembly.
Reverse procedure above to re-assemble unit.
Thermostat Adjustment (CKHATD13 / CKHATD23)
Adjust thermostat with screwdriver.
Fig. 3
Soffit or Stair Riser Installation
1.
Cut opening as for kickspace installation (22 3/8” x
3 5/8”). Allow 3/4” clearance above cabinet doors.
Add supports for unit (Fig.3).
2.
Proceed as for kickspace installation. After
securing unit in opening, install combination of
frame and grille (fig.1).
CAUTION - Disconnect main to de-energize receptacle
before servicing or for electrical inspection.
SERVICING - Remove grille and frame by removing
screws “A”. Remove two screws “B”, and slide out heating assembly. When re-assembling, reverse the
procedure above.
Cleaning
With grille in place - Use vacuum cleaner hose to suck out lint and dirt around grille. Reverse hose on vacuum to
use as a blower to move dust out of enclosure. Reverse hose back to suck out dirt at front area of heater.
With grille removed - Remove two screws “B” at bottom front of heating element assembly. Pull gently to remove
it from enclosure. Swing assembly out. Vacuum inside of enclosure and around heating element assembly.
Reverse procedure above to re-assemble unit.
Thermostat Adjustment (CKHA20D31T)
Adjust thermostat with screwdriver.
Fig 3.
CEILING
HEATER
GRILLE
CABINET DOOR
PARTITION OR
ADDED SUPPORT
3/4”
MIN
M
FAN
FACTORY CONNECTION
208/240 VOLT 675/900 WATTS
3.2 A / 3.7A
1
5
2
6
7
8
3
4
IMPORTANT:
RETIGHTEN ALL LEADS WITH CABLE CLAMP
AFTER RECONNECTING UNINSULATED ENDS OF
UNUSED LEADS WITH WIRE NUTS.
M
FAN
M
FAN
SAFETY SWITCH
SAFETY SWITCH
SAFETY SWITCH
FIELD CONNECTION
208/240 VOLT 1350/1800 WATTS
6.5 A / 7.5 A
FIELD CONNECTION
120 VOLT
RATING
CONNECT
450W/ 3.75A
7-8 (AS SHOWN)
900W/ 7.5A
7-8, 1-2
1350W/ 11.2A
7-8, 1-2, 3-4
1800W/ 15A
7-8, 1-2, 3-4, 5-6
1
5
2
6
7
8
3
4
1
5
2
6
7
8
3
4
NOTE:
If installing unit with factory thermostat, see
supplemental wiring diagram, fig. 4a.
Fig. 4a
Fig. 4
THERMOSTAT
7200960100R04
FACTORY CONNECTION
208/240 VOLT 675/900 WATTS
3.2 A / 3.7A
FACTORY CONNECTION
208/240 VOLT 1350/1800 WATTS
6.5 A / 7.5 A
FACTORY CONNECTION
120 VOLT
Fig. 4
FAN
FAN
FAN
M
M
M
SAFETY SWITCH
SAFETY SWITCH
SAFETY SWITCH
IMPORTANT:
RETIGHTEN ALL LEADS WITH CABLE CLAMP
AFTER RECONNECTING UNINSULATED ENDS OF
UNUSED LEADS WITH WIRE NUTS
Fig. 4a
THERMOSTAT
NOTE:
If installing unit with factory thermostat, see
supplemental wiring diagram, Fig. 4a.
RATING
CONNECT
450W/ 3.75A
7-8 (AS SHOWN)
900W/ 7.5A
7-8, 1-2
1350W/ 11.2A
7-8, 1-2, 3-4
1800W/ 15A
7-8, 1-2, 3-4, 5-6
CATALOG NO.
MOTOR
FAN BLADE
ELEMENT
CUT OUT
(MANUAL)
CUT OUT
(AUTOMATIC)
GRILLE KIT
CKHA20D31
CKHABG
CKHA20D31W
CKHAWG
RKHA20D31W
2000280400RP
5300210100RP
2203260100RP
03005035RP
211A619RP
CKHAWG
REPLACEMENT PART
