background image

 

Replacing 13amp fuse 

The 13amp fuse must be ASTA approved to BS1362. The fuse may be replaced by pulling out the fuse holder, marked 
‘fuse’, on the remote switch assembly until the fuse is dislodged. The new fuse should then be located and held in position 
while the fuse holder is pushed back into position. 

 
 

Circuit Diagram 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Recycling 

For electrical products sold within the European Community. 

At the end of the electrical products useful life it should not be disposed of with household waste. Please recycle 
where facilities exist. Check with your Local Authority or retailer for recycling advice in your country.

 

 
 

After Sales Service

 

Your product is guaranteed for two years from the date of purchase. 
Within this period, we undertake to repair or exchange this product free of charge (subject to availability) provided it has 
been installed and operated in accordance with these instructions.  
Your rights under this guarantee are additional to your statutory rights, which in turn are not affected by this guarantee. 
Should you require after sales service you should contact our customer services help desk on 0845 600 5111.  It would 
assist us if you can quote the model number, series, date of purchase, and nature of the fault at the time of your call.  The 
customer services help desk will also be able to advise you should you need to purchase any spares. 
Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing 
you with a satisfactory service. 

 

Please retain your receipt as proof of purchase. 

 

This product complies with the European Safety Standard EN60335-2-30 and the European Standard for Electromagnetic Compatibility 

(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 89/336. 

 

Dimplex UK Limited  

UK customer help line 8.00am–5.00pm Mon-Fri and 8:30am-1.00pm Sat (October-March)  

Millbrook House 
Grange Drive  

Technical Services:   Tel. 

0845 600 5111 

Hedge End            

 

          Fax. 

01489 773053 

Southampton  

e-mail 

[email protected]  

Hampshire  SO30 2DF

 

 

 

 

Republic of Ireland 

01 8424833

 

 
 
[c] Dimplex UK Limited 
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex UK Limited.

 

 

Summary of Contents for BFH24R

Page 1: ...eater is more easily fitted during the installation of new temporarily moved from their position against the w necessary to remove the back of the unit in order to gain access to carry out the w Before installing the unit consider the location w The electrical supply and cable length Position heater to deliver heat effectively w work surfaces etc Minimum plinth height of 120mm and minimum furnitur...

Page 2: ...he terminal block from its fixing while making connections to it 3 Fitting the Rear Support Bracket The heater is supplied with a rear support bracket Fit to the back of the appliance with the two screws supplied Adjust the rear support bracket so that the vertical distance from the underside of the appliance to bottom of the rear support bracket equals the vertical distance from the floor in the ...

Page 3: ...time to time it may be necessary to remove the heater from the furniture unit so that the interior of the heater and the heater compartment can be cleared of any accumulated dust or fluff by means of a vacuum cleaner fig 2 To remove unscrew the six fixing screws and withdraw the appliance from the plinth To gain access to the inside of the appliance remove the screws securing the top cover Clean t...

Page 4: ...fter sales service you should contact our customer services help desk on 0845 600 5111 It would assist us if you can quote the model number series date of purchase and nature of the fault at the time of your call The customer services help desk will also be able to advise you should you need to purchase any spares Please do not return a faulty product to us in the first instance as this may result...

Reviews: