Important Safety Advice
When using electrical appliances, basic
precautions should be followed to reduce
the risk of fire, electric shock, and injury to
persons, including the following:
If the appliance is damaged, check immediately
with the supplier before installation and
operation.
Do not use this appliance in the immediate
surroundings of a bath, shower or swimming
pool.
Do not use outdoors.
This appliance must not be located immediately
above or below a fixed socket outlet or
connection box.
WARNING
: The appliance carries
the Warning Symbol indicating that it
must not be covered or has a Do not
cover label. Do not cover or obstruct
in any way the heat outlet grille located
underneath the appliance Overheating
will result if the appliance is accidentally
covered. Do not place material or garments
on the appliance, or obstruct the air circulation
around the appliance, for instance by curtains
or furniture, as this could cause overheating
and a fire risk.
In the event of a fault unplug the
heater.
Unplug the appliance when not
required for long periods.
The supply cord
must be placed on the right hand side of the
heater away from the heat outlet underneath
the appliance.
This appliance is not intended for use by
persons
(including
children)
with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible for
their safety.
Children should be supervised to ensure they
do not play with the appliance.
Prior to cleaning or other maintenance, the
appliance must be disconnected from the
supply mains.
The appliance must be positioned so that the
plug is accessible.
If the supply cord is damaged it must be
replaced by the manufacturer or service agent
or similarly qualified person in order to avoid
a hazard.
CAUTION
: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an
external switching device, such as a timer,
or connected to a circuit that is regularly
switched on and off by the utility.
CAUTION
- Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
DO NOT use this heater with a programmer,
timer, separate remote-control system or
any other device that switches the heater on
automatically, since a fire risk exists if the
heater is covered or positioned incorrectly.
WARNING: The heater must not be used if
the glass panels are damaged.
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
General
Unpack the appliance carefully and retain the
packaging for possible future use, in the event of
moving or returning the appliance to your supplier.
These models are designed to be free standing and
are normally positioned against a wall.
The appliance incorporates a flame effect, which
can be used with or without heati
ng, so that the
comforting effect may be enjoyed at any time of the
year. Using the flame effect on its own only requires
little electricity.
A choice of 1kW or 2kW heat output is provided by the
fan heater, which is located at the bottom of the unit.
Before connecting the
appliance
check that the
supply voltage is the same as that stated on the
appliance
.
Please note: Used in an environment wh
ere
background noise is very low, it may be possible
to hear a sound which is related to the operation of
the flame effect. This is normal and should not be a
cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE
EARTHED.
This appliance must be used on an AC ~ supply
only and the voltage marked on the appliance must
correspond to the supply voltage.
Before switching on, please read the safety warnings
and operating instructions.
Controls
- see
Fig. 2
Three switches provide a choice of heat settings. A
switch is in the ON position when the side with the
markings on (i.e.
I
,
I
, or
II
) is pushed in.
Switch 1 (I)
Controls the electricity supply to the
heater and the flame effect.
Note: This switch must be in the ON (I) position
for heater to operate with or without
heat.
Switch 2 (I)
Provides 1kW heat output
Switch 3 (II)
Provides 2kW heat output with
switch 2 in the ON positon also.
