Important Safety Advice
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electrical shock
and injury to persons, including the following:
If the appliance is damaged, check with the supplier before
installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower
or swimming pool.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
Do not cover the heater. Do not place material or garments
on the heater, or obstruct the air circulation around the heater,
for instance by curtains or furniture, as this could cause
overheating and a fire risk.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they do
not play with the appliance. Do not use this heater in series
with a thermal control, a program controller, a timer or any
other device that switches on the heat automatically, since a
fire risk exists when the heater is accidentally covered or
displaced.
Ensure that furniture, curtains or other combustible material
are positioned no closer than 1 metre from the heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we do
not recommend its use on deep pile carpets or on long hair
type of rugs.
The appliance must be positioned so that the plug is
accessible.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified person
in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
This heater is not equipped with a device to control the
room temperature. Do not use this heater in small rooms
when they are occupied by persons not capable of leaving
the room on their own, unless constant supervision is
provided.
Warning: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not be
supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on
and off by the utility.
General
Unpack the heater carefully and retain the packaging for possible
future use, in the event of moving or returning the fire to your supplier.
These models are designed to be free standing and are normally
positioned against a wall.
The fire incorporates a flame effect, which can be used with or without
heati
ng, so that the comforting effect may be enjoyed at any time of
the year. Using the flame effect on its own only requires little electricity.
A choice of 1kW or 2kW heat output is provided by the fan heater,
which is located at the bottom of the unit.
Before connecting the heater check that the supply voltage is the
same as that stated on the heater.
Please note: Used in an environment wh
ere background noise is very
low, it may be possible to hear a sound which is related to the operation
of the flame effect. This is normal and should not be a cause for
concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage. Before
switching on, please read the safety warnings and operating
instructions.
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Controls
- see
Fig. 2
These switches provide a choice of heat settings, The appliance is in
standby mode when the mainslead is plugged in. This is indicated by
the red neon behind the flame effect screen.
The two selector switches are in the ON position when the side with
the markings on (i.e.
I
, or
II
) is pushed in.
Selector switch 1 (0)
Controls the electricity supply to the
heater and flame effect. Press for ‘ON’ and
‘Standby’. If both selector switches 2 and 3
are in the OFF position, the product works
on flame effect only.
Selector Switch 2 (I)
Provides 1kW heat output
Selector Switch 3 (II)
Provides 2kW output with switch 2
Remote
control
- see
Fig. 6
The maximum range of use is ~ 15metres.
Warning: It takes time for the receiver to respond to the transmitter.
Do not press the buttons more than once within two seconds for correct
operation.
Battery information
- see
Fig. 6
1.
Slide open the battery cover on the back of the remote control
2.
Install AAA batteries into the remote control
3.
Replace the battery cover.
Discard leaking batteries
Dispose of batteries in the proper manner according to provincial and
local regulations.
Any battery may leak electrolyte if mixed with a different battery type,
if inserted incorrectly, if all the batteries are not replaced at the same
time, if disposed of in a fire, or if an attempt is made to charge a
battery not intended to be recharged.
Lamp Replacement
- see
Fig. 3, Fig. 4 and Fig. 5
The lamps are located behind the back panel. To gain access to the
lamps, the screws indicated in
Fig. 3
which secure the back panel,
must be removed.
Remove and slide out panel as indicated on
Fig. 4
.
Remove the defective lamp by unscrewing it as shown in
Fig. 5
.
Replace with a 60W E14 SES Clear candle lamp. Take care not to
over-tighten the lamp.
Refit the back panel and secure with the screws.
Thermal Safety Cut-out
The built-in overheat cut-out switches off the appliance automatically
in the event of a fault. If this occurs switch off the appliance or
disconnect the mains plug from the socket. After a short cooling down
phase, the appliance is ready for use again. If the fault should occur
again, see your local dealer.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE ATTEMPTING ANY MAINTENANCE.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully with
a soft cloth. DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush attachment
of a vacuum cleaner should occasionally be used to clean the outlet
grille of the fan heater.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it should
not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or
retailer for recycling advice in your country.
- Club, CLB20R
- Courchevel, CVL20
UK
