background image

Precautions 

1.

Storage should be dry, clean and ventilated; 

2.

Should be equipped with shelves or cabinets for linear lights; 

3.

Should have corresponding fire prevention measures; 

4.

Linear lights (including accessories) should be categorize for managed, storage and labeled; 

5.

Keep the instructions and packing boxes of lighting fixtures, accessories and light sources etc. for future checking; 

6.

The lighting fixture should be wiped and maintained regularly. It is recommended to maintain once or twice a 
quarter. 

7.

When wiping the fixture, use a clean, soft cloth. After wiping, put it in a clean transparent plastic bag and an 
appropriate place; 

8.

Do not rinse directly with water. 

Warranty Instruction 

1.

Under normal conditions of use, the product is warranted for three years. During the warranty period, the 
product fails, if the product is inspected by the company, the product of the same model will be replaced free 
of charge.   

2.

One of the following conditions is not covered by the warranty: 

        (1) Damage to the product if it is not used as required by the instructions; 
        (2) The situation in which the user disassembles the internal parts and improperly damages the product; 
        (3) The product is seriously damaged or deformed. 

Storage Management 

1.

During the installation, ensure the wire is connected properly base on the marking of the wire end and the 
electricity operation is prohibited. 

2.

Electronic components such as power supplies are strictly prohibited from being disassembled; 

3.

The lighting fixture should be wiped and maintained regularly. It is recommended to maintain once or twice a 
quarter. Pay attention to electricity safety and check the fastening of the installation parts; 

4.

Avoid hit by external objects when using. 

Use Maintenance 

Summary of Contents for AP2114B









Reviews: