Digiway DWPD102A Series Installation Manual Download Page 16

Page: 16 / 52

DIGIWAY PLUS

INSTALLATION MANUAL

ADJUSTMENTS

The maximum speed, the torque and the pause time are automatically calculated by the system during the door calibration.

The maximum speed, the torque and the pause time are automatically calculated by the system during the door calibration.
If you prefer to adjust the parameters manually to tailor the door travel, then it is necessary to access the submenu MAIN FUNCTIONS

If you prefer to adjust the parameters manually to tailor the door travel, then it is necessary to access the submenu MAIN FUNCTIONS
from the main menu. See following table for the explanation of the parameters.

from the main menu. See following table for the explanation of the parameters.
Each parameter can be adjusted using the keyboard buttons or

Each parameter can be adjusted using the keyboard buttons or transmitter keys.

transmitter keys.

Main Functions

Description

Values

NOTES

Open Speed

Sets the maximum speed reached by the
door during opening.

0 - 100%

At the end of the door calibration the systems sets automatically the

max open speed

at a special value. By increasing this value, the total

open time can reduce - be aware that in order to respect the end

opening point, the door may slow down before reaching the max speed.

Close Speed

Sets the maximum speed reached by the
door during closing.

0 - 100%

At the end of the door calibration the systems sets automatically the

max close speed

at a special value. By increasing this value, the total

close time can reduce - be aware that in order to respect the end closing

point, the door may slow down before reaching the max speed.

Pause Time

Pause time - this is the time remains
open before automatically closing again

1 - 99 SEC.

The preset factory value is 10 sec.

Open Torque

Max torque of the door during opening.

0 - 100%

The max opening torque is set automatically by the system at the end of
the door calibration to the max value (100 %). In the case of very light or

sensitive doors, it may be necessary to decrease this value.

Close Torque

Max torque of the door during closing

0 - 100%

The max closing torque is set automatically by the system, at the end

of the door calibration, to the max value ( 100 %). Decrease this value

in case of very light or sensitive doors, or to respect the regulations for

disabled access.

Velocity

Velocity of the door: rapidity of the door
to reach the max speed set, and to
mantain this value along all its travel.

0 - 100%

The default value for this parameter is 70%. The more this value, the

less is the total travel time, because the door maintains a high value of

speed for a longer time. Values too high for this parameter can cause

“door bounce”, especially for heavy doors (see motion diagram).

Open Speed

|||||||||||||||||...........................

45%

To increase the value press the key UP

To increase the value press the key UP
To decrease the value press the key DOWN

To decrease the value press the key DOWN
Press OK to confi rm.

Press OK to confi rm.
Press ESC to exit without saving.

Press ESC to exit without saving.
A bar will appear on the display, proportional to the value and the numeric value of the parameter .

A bar will appear on the display, proportional to the value and the numeric value of the parameter .

ESC

DOWN

ESC

CURRENT CALCULATION CYCLES

At the end of the door calibration, the door will operate normally.

At the end of the door calibration, the door will operate normally.
However, to complete the calibration the system needs 2 more complete cycles to calculate the 2 currents ( called “i” and “I”) necessary for

However, to complete the calibration the system needs 2 more complete cycles to calculate the 2 currents ( called “i” and “I”) necessary for
obstacle management.

obstacle management.

Until the 2 cycles are completed, the external LED LP will blink RED.

Until the 2 cycles are completed, the external LED LP will blink RED. During the 2 cycles, before the completion of

During the 2 cycles, before the completion of

this calculation, if the door knocks meets an obstacle, the obstacle sensitivity used will be the factory value, which may not fi t perfectly with

this calculation, if the door knocks meets an obstacle, the obstacle sensitivity used will be the factory value, which may not fi t perfectly with
the door characteristics, therefore:

the door characteristics, therefore:

“It is highly recommended to ensure the door completes these 2 cycles without any interruption. When completed,

“It is highly recommended to ensure the door completes these 2 cycles without any interruption. When completed,
the external LED will illuminate Green, and the door calibration is completed.”

the external LED will illuminate Green, and the door calibration is completed.”

Motion

diagram

STEPIV : ADJUSTMENTS

Velocity = 0%

Velocity = 100%

Vmax