Digitus DN-95301 User Manual Download Page 16

Page: 16 / 51

Format

logout

Mode

Privileged Mode

ping

This command is used to proceed ping destination host

Format

ping <

A.B.C.D

Mode

Privileged Mode

reload

This command is used to reboot system

Format

reload

Mode

Privileged Mode

save

This command is used to save configuration

Format

save

Mode

Privileged Mode

show

This command is used to show configured data
1) show qos

This command display class of service information
1.1) show qos cos

This command display the cos mapping

Format

show qos cos

Mode

Privileged Mode

1.2) show qos queue-settings

This command display the queue-settings mapping

Format

show qos queue-settings

Mode

Privileged Mode

1. 3) show qos advanced

This command display qos advanced mode information
1.3.1) show qos advanced mode

This command display mode of qos

Format

show qos advanced mode

Mode

Privileged Mode

1.3.2) show qos advanced dscp

This command display qos dscp mapping

Format

show qos advanced dscp

Mode

Privileged Mode

1.3.3) show qos advanced ip-precedence

This command display qos ip precedence mapping

Format

show qos advanced ip-precedence

Mode

Privileged Mode

1.4) show qos port-based

This command is used to display class of service information
1.4.1) show qos port-based port

This command display class of service information

Format

show qos port-based port <

port-ID

Mode

Privileged Mode

1.4.2) show qos port-based all

Layer 2/2+ Management Switch Series

Summary of Contents for DN-95301




















































Search results

Summary of Contents for DN-95301

Reviews:

Related manuals for DN-95301

Brands by name

Popular brands

Digitus DN-95301, User Manual

Search results

Summary of Contents for DN-95301

Reviews:

Related manuals for DN-95301

Brands by name

Popular brands