DigitaLinx DL-HD70LS Owner'S Manual Download Page 10

DL-HD70LS Owners Manual

10

Connecting IR Control

Source Device Control using IR

Attach the IR emitter to the IR receiver of the source device, insert the TS 3.5 mm plug of the emitter to the 

IR 

OUT

 port of the DL-HD70LS transmitter. Insert the TS 3.5 mm plug of the IR receiver (eye) to the

 IR IN 

port of the 

DL-HD70LS receiver.  Point the source device IR remote at the display location where the IR receiver is located, 

IR signals will now travel through HDBaseT to the DL-HD70LS transmitter side where the IR emitter is attached 

to the source device. 

Attach the IR emitter to the IR receiver of the display device, insert the TS 3.5 mm plug of the emitter to the 

IR 

OUT

 port of the DL-HD70LS receiver. Insert the TS 3.5 mm plug of the IR receiver (eye) to the IR IN port of the 

DL-HD70LS transmitter.  Point the source device IR remote at the source device location where the IR receiver 

is located, IR signals will now travel through HDBaseT to the DL-HD70LS receiver side where the IR emitter is 

attached to the display device.

The DL-HD70LS is capable of transmitting bi-directional IR signals through the HDBaseT circuit. The DL-HD70LS 

comes with 1 IR receiver (eye) and 1 IR emitter (flasher) so you can control devices from either end of the 

extender circuit.

Remote Display using IR

To pass 3rd party IR system signals through the DL-HD70LS, such as a control system, connect the TS connector 

of the IR-AC coupling cable (purchased separately) to the IR output port of the control system and connect the 

TRS connector of the IR-AC cable to the IR IN to either transmitter or receiver of the DL-HD70LS.

Source / Display Control from Control System

Passing IR Signals:

The DL-HD70LS is capable of passing IR signals between 33 and 55 KHz. To prevent damage to 

any of the electronics, the extenders should be powered off while inserting or removing any IR 

components. Inserting an IR transmitter into the IR IN port may damage the IR circuit for that 

extender.

Tip: +5V DC

Tip: IR Signal

Ring: IR Signal

Sleeve: Ground (GND)

Sleeve: Ground (GND)

Note

Voltage on Tip from RX may be differnt for non Liberty Devices

To DL-HD7LS 

Tx or Rx Extender IR Input

To Control system or

IR hub output

+5V DC Lifted

IR Signal

Ground (GND)

Summary of Contents for DL-HD70LS
















Reviews: