CAMERA SETTINGS
CONNECTION
※
ATTENTION
1. Do not rotate
①
more than 360˚.
2. Do not twist
②
many times unnecessarily.
SETUP
FUNTION
SUMMARY
when using BUILT-IN lens,
the type of the lens is able to fix
MANUAL: 1/60(50) ~
1/120,000sec, x2~ x128
WHITE BAL.
ATW, MANUAL, AWC
ATW: 1,800 ~10,500
˚
K
BACKLIGHT
OFF, LOW, MIDDLE, HIGH
Backlight compensation
AGC
NORMAL, HIGH,OFF
the Brightness can be adjusted(1 ~ 70)
when AGC is turned off,
DNR does not operate.
when AGC is turned off,
SENS-UP does not operate.
SPECIAL
Refer to the bottom
Saved all the setting menu,
then exits.
uppercase or lowercase, OFF
maximum length for the name
/numeral 0~9/-, null
display is limited 15letters.
AUTO :
dayatime
→
color mode ,
night-time
→
B/W mode
B/W : Always B/W mode
COLOR: Always color mode
EXTERN
:
CDS
EXTERNAL
SIGNAL
INPUT
LL mode: you can adjust
desired phase from 0
˚
~ 359
˚
,
auto detection
MATION
ON mode: AREA(4 programmable
DETECTION
zone /SIZE), the word
MOTION DETECTED" appear on the
screen when movement is detected
ON mode:AREA(4 programmable
zone) /SIZE/TONE
MIRROR
OFF, ON
set a horizontal image inversion.
the available range
of level is 0 ~ 31.
returns to the level which was set
by the manufacturer for shipment.
save the SPECIAL MENU and then
PRIVACY
OFF, ON
SHARPNESS
OFF, ON(=8)
RESET
OFF, ON
RERURN
CAMER ID
DAY NIGHT
AUTO, B/W, EXTERN, COLOR
SYNC
INT, LL
SENS-UP
AUTO(=X6), OFF
EXIT
SHUTTER
ESC, MANUAL, FLK, OFF
DNR
MIDDLE, HIGH, OFF, LOW
LENS
CAUTION :
Check for polarity when using a DC 12V / AC 24V.
CAMERA SETING ANGLE
CAMERA SETTINGS
CONTROL BOARD
CONNECTION
※
ATTENTION
1. Do not rotate
①
more than 360˚.
2. Do not twist
②
many times unnecessarily.
SW2
SW3
SW1
CON2
SETUP
FUNTION
SUMMARY
when using BUILT-IN lens,
the type of the lens is able to fix
MANUAL: 1/60(50) ~
1/120,000sec, x2~ x128
WHITE BAL.
ATW, MANUAL, AWC
ATW: 1,800 ~10,500
˚
K
BACKLIGHT
OFF, LOW, MIDDLE, HIGH
Backlight compensation
AGC
NORMAL, HIGH,OFF
the Brightness can be adjusted(1 ~ 70)
when AGC is turned off,
DNR does not operate.
when AGC is turned off,
SENS-UP does not operate.
SPECIAL
Refer to the bottom
Saved all the setting menu,
then exits.
uppercase or lowercase, OFF
maximum length for the name
/numeral 0~9/-, null
display is limited 15letters.
AUTO :
dayatime
→
color mode ,
night-time
→
B/W mode
B/W : Always B/W mode
COLOR: Always color mode
EXTERN
:
CDS
EXTERNAL
SIGNAL
INPUT
LL mode: you can adjust
desired phase from 0
˚
~ 359
˚
,
auto detection
MATION
ON mode: AREA(4 programmable
DETECTION
zone /SIZE), the word
MOTION DETECTED" appear on the
screen when movement is detected
ON mode:AREA(4 programmable
zone) /SIZE/TONE
MIRROR
OFF, ON
set a horizontal image inversion.
the available range
of level is 0 ~ 31.
returns to the level which was set
by the manufacturer for shipment.
save the SPECIAL MENU and then
returns to the SETUP MENU
PRIVACY
OFF, ON
SHARPNESS
OFF, ON(=8)
RESET
OFF, ON
RERURN
CAMER ID
DAY NIGHT
AUTO, B/W, EXTERN, COLOR
SYNC
INT, LL
SENS-UP
AUTO(=X6), OFF
EXIT
SHUTTER
ESC, MANUAL, FLK, OFF
DNR
MIDDLE, HIGH, OFF, LOW
LENS
KEY
BUTTON
OSD
BUTTON
Zoom
Focus
Control
Buttons
BUTTON
ID
Buttons
BUTTON
CAUTION :
Check for polarity when using a DC 12V / AC 24V.
CAMERA SETING ANGLE
FUNCTIONAL OF CONTROL BOARD
1. SW1 Joystick
The function of SW1 joystick are camera zoom in/out and OSD control.
a) Press SW3 button for 2 seconds until red LED light around the camera
lens flickers 3 times. And the function of SW1 is switched to control Omni
Focus Zoom ON/OFF.
b) Press SW3 button for 2 seconds until red LED light around the camera
lens flickers 3 times. And the function of SW1 is switched to control OSD
menu.
2. SW2
The camera ID number is set by pushing SW2 switches.
(
※
1,2,4,8(BCD code) means ID number, and ID contains 10 numbers from
0 to 9.) for the IR remote only
3. CON2
Video Test output connector
Omni
‐
Focus
Remote
Control
Instructions
1. Check
the
Dip
switch
(SW4)
for
camera
ID
(Default
is
0)
2. Point
the
remote
control
towards
the
camera,
then
press
and
hold
[0]
until
the
Red
LED
light
start
flashing.
3. Press
and
hold
the
KEY
button,
until
LED
turns
a
solid
RED.
4. Press
the
Plus
sign
(+)
to
ZOOM
IN,
Minus
sign
(
‐
)
to
ZOOM
OUT
5. Press
the
[ENT]
button
to
enter
the
setup
Menu
and
press
[KEY]
button
to
exit.