manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 70

2–40

Internal Architecture

29 September 1997 – Subject To Change

Floating-Point Control Register

2.9 Floating-Point Control Register

Figure 2–3 shows the format of the floating-point control register (FPCR) and 
Table 2–10 describes the fields.

Figure 2–3 Floating-Point Control Register (FPCR) Format

Table 2–10 Floating-Point Control Register Bit Descriptions

(Sheet 1 of 2)

Name

Extent

Description (Meaning When Set)

SUM

<63>

Summary bit. Records bitwise OR of FPCR exception bits. Equal to 
FPCR<57 | 56 | 55 | 54 | 53 | 52>

INED

<62>

Inexact disable. Suppress INE trap and place correct IEEE nontrap-
ping result in the destination register if the 21164PC is capable of 
producing correct IEEE nontrapping result.

UNFD

<61>

Underflow disable. Subset support: Suppress UNF trap if UNDZ is 
also set and the /S qualifier is set on the instruction.

UNDZ

<60>

Underflow to zero. When set together with UNFD, on underflow, 
the hardware places a true zero (all 64 bits zero) in the destination 
register rather than the denormal number specified by the IEEE stan-
dard.

31

00

63

32

55

56

57

58

59

60

61

62

INVD
DZED

INV
DZE
OVF
UNF
INE
IOV
DYN_RM
UNDZ
UNFD

RAZ/IGN

OVFD

50

51

52

53

54

48

49

INED
SUM

RAZ/IGN

LJ-05358.AI4

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands