manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 277

29 September 1997 – Subject To Change

Electrical Data

9–21

Power Supply Considerations

Table 9–16 lists the clock test modes.

9.4.6 IEEE 1149.1 (JTAG) Performance

Table 9–17 lists the standard mandated performance specifications for the 
IEEE 1149.1 circuits.

9.5 Power Supply Considerations

For correct operation of the 21164PC, all of the Vss pins must be connected to 
ground, all of the Vdd pins must be connected to a 3.3-V ±5% power source, and all 
of the Vddi pins must be connected to a 2.5-V ±0.1 V power source. This source 
voltage should be guaranteed (even under transient conditions) at the 21164PC pins, 
and not just at the PCB edge.

Table 9–16 Clock Test Modes

clk_mode_h

Mode

<1>

<0>

Notes

Normal (1×) clock mode

0

0

Normal (1×) clock mode

0

1

Symmetrator is enabled.

Clock reset

1

0

Clock reset

1

1

Symmetrator is enabled.

Table 9–17  IEEE 1149.1 Circuit Performance Specifications

Item

Specification

trst_l is asynchronous. Minimum pulse width.

4 ns

trst_l setup time for deassertion before a transition on tck_h.

4  ns

Maximum acceptable tck_h clock frequency.

16.6 MHz

tdi_h/tms_h setup time (referenced to tck_h rising edge).

4 ns

tdi_h/tms_h hold time (referenced to tck_h rising edge).

4 ns

Maximum propagation delay at pin tdo_h (referenced to tck_h falling 
edge).

14 ns

Maximum propagation delay at system output pins (referenced to tck_h 
falling edge).

20 ns

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands