manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 269

29 September 1997 – Subject To Change

Electrical Data

9–13

AC Characteristics

9.4.2.2 sys_clk-Based Systems

All timing is specified relative to the rising edge of the internal CPU clock.

Table 9–8 shows 21164PC system clock sys_clk_out1_h output timing. Setup and 
hold times are specified independent of the relative capacitive loading of 
sys_clk_out1_h,l, addr_h<39:4>, data_h<127:0>, and cmd_h<3:0> signals.

1

The value 0.2 ns accounts for onchip driver and clock skew.

2

For all system write transactions initiated by the 21164PC, data is driven Tcycle (= 1 cpu_clk) after the 
sys_clk_out1_h pin. For all private write transactions, data is driven coincident with Tcycle (= 0 cpu_clk) the 
driving of index_h<21:4>.

Table 9–8 21164PC System Clock Output Timing (sysclk=T

ø

)

Signal

Specification

Value

Name

sys_clk_out1_h

Output delay    

Tdd

Tsysd

sys_clk_out1_h

Minimum output delay Tmdd

Tsysdm

data_bus_ req_h, data_h<127:0>, 
addr_h<39:4>

Input setup

1.1 ns

Tdsu

data_bus_ req_h, data_h<127:0>, 
addr_h<39:4>

Input hold

0 ns

Tdh

addr_h<39:4>

Output delay

Tdd + 0.2 ns

1

Taod

addr_h<39:4>

Output hold time

Tmdd

Taoh

data_h<127:0>

Output delay

Tdd [+ Tcycle]

2

 + 0.2 ns

1

Tdod

2

data_h<127:0>

Output hold time

Tmdd [+ Tcycle]

2

Tdoh

2

addr_bus_req_h

Input setup

 3.4 ns

Tabrsu

addr_bus_req_h

Input hold

−

1.0 ns

Tabrh

dack_h

Input setup

 3.2 ns

Tntacksu

cack_h

Input setup

3.4 ns

Tntcacksu

cack, dack

Input hold

−

1.0 ns

Tntackh

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands