manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 246

7–12

Initialization and Configuration

29 September 1997 – Subject To Change

Timeout Reset

7.9 Timeout Reset

The instruction fetch/decode unit and branch unit (IDU) contains a timer that times 
out when a very long period of time passes with no instruction completing. When 
this timeout occurs, an internal reset event occurs. This clears sufficient internal state 
to allow the CPU to begin executing again. Registers, IPRs (except as noted in 
Table 7–2), and caches are not affected. Dispatch to the PALcode MCHK trap entry 
point occurs immediately.

MCSR

Cleared

Cleared on chip reset but not on timeout reset.

DC_MODE

Cleared

Cleared on chip reset but not on timeout reset.

MAF_MODE

Cleared

Cleared on chip reset. MAF_MODE<05> 
cleared on timeout reset.

DC_FLUSH

UNDEFINED PALcode must write this register to clear 

Dcache valid bits.

ALT_MODE

UNDEFINED

CC

UNDEFINED CC is disabled on chip reset.

CC_CTL

UNDEFINED

DC_TEST_CTL

<15> cleared

Cleared on chip reset but not on timeout reset.

DC_TEST_TAG

UNDEFINED

DC_TEST_TAG_TEMP UNDEFINED

CBU Registers

CBOX_CONFIG

See Section 5.3.1 for power-up state.

CBOX_CONFIG2

See Section 5.3.4 for power-up state.

CBOX_ADDR

See Section 5.3.2 for power-up state.

CBOX_STATUS

See Section 5.3.3 for power-up state.

Table 7–2 Internal Processor Register Reset State

(Sheet 3 of 3)

IPR

Reset State

Comments

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands