manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

The Digital Equipment Alpha 21164PC is a cutting-edge computing solution that promises unparalleled performance. For in-depth knowledge and optimal usage, it is essential to have access to the comprehensive Hardware Reference Manual. You can now conveniently download this manual for free from manualshive.com, empowering you with complete control over your device.

Share
Download
background image

5–14

Internal Processor Registers

29 September 1997 – Subject To Change

Instruction Fetch/Decode Unit and Branch Unit (IDU) IPRs

5.1.14 Exception Mask (EXC_MASK) Register (10D)

EXC_MASK is a read/write register that records the destinations of instructions that 
have caused an arithmetic trap between EXC_MASK write operations. The destina-
tion is recorded as a single bit mask in the 64-bit IPR representing F0–F31 and 
I0–I31. A write operation to EXC_ SUM clears the EXC_MASK register. 
Figure 5–13 shows the EXC_MASK register format.

Figure 5–13 Exception Mask (EXC_MASK) Register

00

31

32

63

LJ-03485.AI4

I1 I0

I31 I30 I29 .....

F1 F0

F31 F30 F29 .....

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Related manuals for Alpha 21164PC

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
Datasat AP20 Installation And Operating Manual preview
AP20
Brand: Datasat Pages: 32
Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Brand: Cabletron Systems Pages: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Brand: Cabletron Systems Pages: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Brand: Cabletron Systems Pages: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Brand: Cabletron Systems Pages: 2
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Brand: Cabletron Systems Pages: 54
Cabletron Systems Cabletron BRIM-F6 User Manual preview
Cabletron BRIM-F6
Brand: Cabletron Systems Pages: 43
Cabletron Systems Netlink FRX4000 Maintenance Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 60
Cabletron Systems 9E132-15 Appendix preview
9E132-15
Brand: Cabletron Systems Pages: 8
Cabletron Systems TRXI-22 Addendum preview
TRXI-22
Brand: Cabletron Systems Pages: 4
National Instruments NI 9426 Getting Started Manual preview
NI 9426
Brand: National Instruments Pages: 17
QSC DSP-30 Hardware Manual preview
DSP-30
Brand: QSC Pages: 28
Rolls HR11C Owner'S Manual preview
HR11C
Brand: Rolls Pages: 2
Supero Supero SAS-826A User Manual preview
Supero SAS-826A
Brand: Supero Pages: 16
Z Microsystems TranzStor 8X User Manual preview
TranzStor 8X
Brand: Z Microsystems Pages: 51
Ubiquiti LiteBeam M5-23 Quick Start Manual preview
LiteBeam M5-23
Brand: Ubiquiti Pages: 21
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4

Brands by name

Popular brands

Load more brands