manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 138

4–50

Clocks, Cache, and External Interface

29 September 1997 – Subject To Change

21164PC Interface Restrictions

4.9.5.3 FILL to Private READ or WRITE Operation

At the end of the fill, the 21164PC does not begin to drive the data bus until the fifth 
cpu_clk cycle after the sysclk that loads the last dack_h (refer to Figure 4–25). The 
21164PC does not assert data_ram_oe_l until the fifth cycle after the sysclk that 
loads the last dack_h.

Systems requiring more time to turn off their drivers must not send any more 
requests and must use idle_bc_h and data_bus_req_h at the end of the fill to pro-
vide adequate write-to-read spacing to avoid data bus contention.

Figure 4–25 FILL to Private READ or WRITE Operation

4.10 21164PC Interface Restrictions

This section lists restrictions on the use of 21164PC interface features.

4.10.1 Fill Operations After Other Transactions

For a system Bcache read operation (Bcache victim or a system-initiated data move-
ment) followed by a fill operation, the earliest assertion of fill_h by the system is 
dependent upon the CBOX_CONFIG<BC_REG_REG> bit to avoid a read-to-write 
data bus contention. When the BC_REG_REG bit is set, the 21164PC will deassert 
data_ram_oe_l a full sysclk cycle after the final dack_h is detected to allow the 
system adequate time to sample the Bcache read data. See Section 4.9.5.2 for timing 
diagrams and assumptions that must be met by the system.

PCA018

dack_h

index_h<21:4>

cpu_clk

data_h<127:0>

data_ram_oe_l

D0

I0

N

sys_clk_out1_h

I3

D3

N+3

N+1

N+2

N+4

N+5

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands