– 1079 –
44
D
OMAIN
N
AME
S
ERVICE
C
OMMANDS
These commands are used to configure Domain Naming System (DNS)
services. Entries can be manually configured in the DNS domain name to IP
address mapping table, default domain names configured, or one or more
name servers specified to use for domain name to address translation.
Note that domain name services will not be enabled until at least one name
server is specified with the
command and domain lookup is
enabled with the
command.
ip domain-list
This command defines a list of domain names that can be appended to
incomplete host names (i.e., host names passed from a client that are not
formatted with dotted notation). Use the
no
form to remove a name from
this list.
S
YNTAX
[
no
]
ip domain-list
name
name
- Name of the host. Do not include the initial dot that
separates the host name from the domain name.
(Range: 1-68 characters)
D
EFAULT
S
ETTING
None
Table 139: Address Table Commands
Command
Function
Mode
Defines a list of default domain names for incomplete
host names
GC
Enables DNS-based host name-to-address translation
GC
Defines a default domain name for incomplete host
names
GC
Creates a static IPv4 host name-to-address mapping
GC
Specifies the address of one or more name servers to use
for host name-to-address translation
GC
Creates a static IPv6 host name-to-address mapping
GC
Clears all entries from the DNS cache
PE
Deletes entries from the host name-to-address table
PE
Displays the configuration for DNS services
PE
Displays entries in the DNS cache
PE
Displays the static host name-to-address mapping table PE
Summary of Contents for DG-GS4826S
