Digisol DG-GS1550 Management Manual Download | Manualshive

Page: 80 / 665

background image

Configuring the Switch

3-34

3

Setting the System Clock

Simple Network Time Protocol (SNTP) allows the switch to set its internal clock
based on periodic updates from a time server (SNTP or NTP). Maintaining an
accurate time on the switch enables the system log to record meaningful dates and
times for event entries. You can also manually set the clock using the CLI. (See
"calendar set" on page 4-66) If the clock is not set, the switch will only record the
time from the factory default set at the last bootup.

When the SNTP client is enabled, the switch periodically sends a request for a time
update to a configured time server. You can configure up to three time server IP
addresses. The switch will attempt to poll each server in the configured sequence.

Setting the Time Manually

You can set the system time on the switch manually without using SNTP.

CLI

– This example sets the system clock time and then displays the current time

and date

.

Configuring SNTP

You can configure the switch to send time synchronization requests to time servers.

Command Attributes

•

SNTP Client

– Configures the switch to operate as an SNTP client. This requires

at least one NTP or SNTP time server to be specified in the SNTP Server field.
(Default: Disabled)

•

SNTP Poll Interval

– Sets the interval between sending requests for a time update

from a time server. (Range: 16-16384 seconds; Default: 16 seconds)

•

SNTP Server

–

Sets the IP address for up to three time servers. The switch

attempts to update the time from the first server, if this fails it attempts an update
from the next server in the sequence.

Console#calendar set 17 46 00 october 18 2008

Console#show calendar

17:46:11 October 18 2008
Console#

«
...
78
79
80
81
82
...
»

Summary of Contents for DG-GS1550


























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DG-GS1550

SANbox 5000 Series

Brand: Qlogic Pages: 8

Premasreg 716 Series

Brand: S+S Regeltechnik Pages: 32

Brand: Comtrend Corporation Pages: 2

Brand: G-Lab Pages: 12

IES8242MPp9H-S-DR

Brand: OTS Pages: 3

Brand: GeoVision Pages: 7

Brand: KanexPro Pages: 35

Brand: C&C TECHNIC Pages: 2

Brand: KinAn Pages: 5

Brand: WTI Pages: 56

Brand: Labgear Pages: 8

Brand: Omega Engineering Pages: 16

Brand: Kramer Pages: 33

Brand: ATEN Pages: 15

Brand: Tripp Lite Pages: 9

Brand: Unipoe Pages: 6

Brand: ATEN Pages: 300

Brand: Audioplex Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands