background image

WebColour - Web Based LED Control 

User Manual 

7.0 - 23 November 2020 

 

 

digilin.com.au 

Page 5 of 25 

+617 3899 1267 

 

Determining the IP Address 

If using a system that is NetBIOS enabled, the IP Address of the WebColour can be determined by pinging 

the unit name. 

 

To do this, open a command prompt window, and enter the command “ping unitname”.  The result will 

include the IP Address of the WebColour.  An example of this is given in Figure 1, where the Unit Name is 

webcolour and the returned IP address is 192.168.0.8. 

 

If, however you are not using a NETBIOS enabled system or you have forgotten the Unit Name, there are 

still options.  Probably the best is the use of a broadcast ping and arp commands. 

 

To do this, you will need to know your computers IP address and netmask.  In a command prompt, you then 

need to ping broadcast address.  The broadcast address is the IP address with 255 in the positions where 

there are 0’s in the netmask.  For example, on a computer with an IP address of 192.168.0.23 and a netmask 

of 255.255.255.0, the broadcast address is 192.168.0.255.  Note that it may look like there is no response to 

the ping command. 

 

The next step is to enter the command “arp –a”

.  This will provide a list of all the IP addresses that the 

computer now knows (after the broadcast ping).  One of these addresses will be the WebColour.  

Unfortunately, each returned address must be tested (by attempting to access it in the web browser) to 

determine which is the WebColour.  This command sequence is shown for the above example in Figure 2. 

C:\Users\Craig.DIGILIN>ping webcolour 
 
Pinging webcolour [192.168.0.8] with 32 bytes of data: 
Reply from 192.168.0.8: bytes=32 time<1ms TTL=255 
Reply from 192.168.0.8: bytes=32 time<1ms TTL=255 
Reply from 192.168.0.8: bytes=32 time<1ms TTL=255 
Reply from 192.168.0.8: bytes=32 time<1ms TTL=255 
 
Ping statistics for 192.168.0.8: 
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), 
Approximate round trip times in milli-seconds: 
    Minimum = 0ms, Maximum = 0ms, Average = 0ms 

Figure 1.  Using the Ping Command to determine the IP Address.

 

Summary of Contents for WebColour


























Reviews: