manualshive.com logo in svg

Digi One TS W, User Manual

Share
Download
Digi One TS W User Manual Download Page 19

Chapter 5

 Configuring the IP Address

 19

Options for Configuring the IP Address and Mask

The device server IP address can be configured using the following 
methods:

•

With Digi Port Authority-Remote, a Digi utility on the Software and 
Documentation CD.

•

By updating the ARP table on a server and then pinging the Digi 
device (called ARP-Ping, see "Configuring the IP Address Using 
ARP-Ping" on page 20).

•

From the command line using the set config command ("Configuring 
the Ethernet Interface from the Command Line" on page 21

.)

•

Using a RARP server ("Configuring an IP Address using DHCP and 
RARP" on page 22.)

•

Using a DHCP server ("Configuring an IP Address using DHCP and 
RARP" on page 22.)

The IP address and mask can also be changed using the web interface. 
This method, however, does not work for the initial IP address 
configuration. 

Device Support: Digi Port Authority-Remote and ARP-Ping for IP Address 
Configuration

Not all Digi devices can use Digi Port Authority-Remote and ARP-Ping for 
IP address configuration. To determine if you can use these features, find 
the hardware label on your Digi device and then use the table below to 
determine whether this feature is available:

Configuring the Ethernet Interface with Digi Port Authority-Remote

Use this section to configure an initial IP address, subnet mask, and default 
gateway using Digi Port Authority-Remote. This procedure cannot be used 
to change the IP address, but only to assign the initial IP address. It also 
cannot be used if a DHCP server is active. 

Starting Point

This procedure assumes the following:

•

That your Digi device supports this feature. See "Device Support: 
Digi Port Authority-Remote and ARP-Ping for IP Address Configura-
tion" on page 19.

•

That your Digi device is connected to the Ethernet network.

Chapter 5

C o n f i g u r i n g   t h e   I P   A d d r e s s

Device

Part Number

Revision Required

Digi One IA RealPort

50000764-01 

F or higher

Digi One RealPort

50000723-01

J or higher

PortServer TS 2

50000723-02

J or higher

PortServer TS 4

50000723-03

G or higher

Summary of Contents for One TS W





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands