Diamond D1 250.2 Installation Manual Download Page 7

7

Mounting Locations

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will 

void your warranty.

         

Trunk Mounting

Mounting the amplifier vertically will provide adequate cooling of the amplifier. If you will be mounting 

it to an existing panel, be sure it’s not prone to excessive vibration (such as mounting to the back of a 

subwoofer enclosure). Excess vibration is not recommended for electronic products, amplifiers included. 

Mounting the amplifier flat on the floor of the trunk will provide the best cooling, however be cautious 

not to deposit baggage and other items over the top of the amplifier.  Mounting the amplifier upside 

down to the rear deck of the trunk will NOT  provide adequate heat dissipation and will severely affect 

the performance of the amplifier and is not recommended.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as you provide a sufficient 

amount of air for the amplifier to cool itself. If you are going to mount the amplifier under the seat of 

the vehicle, you must have at least 1 inch (2.54cm) of air gap around the amplifier’s heatsink. Mounting 

the amplifier with less than 1 inch (2.54cm) of air gap around the amplifier’s heatsink in the passenger 

compartment will not provide proper cooling and will severely affect the performance of the amplifier 

and is not recommended.

         

Vehicle Electrical System Requirements         

Amplifiers (regardless of brand name) will put an increased load on the vehicle’s battery and charging 

system. DAT recommends checking your alternator and battery condition to ensure that the electrical 

system has enough capacity to handle the increased load of your stereo system. Original equipment 

electrical systems which are in good condition should be able to handle the extra load of any DAT ampli-

fier without problems, although battery and alternator life can be reduced depending on your individual 

listening habits. To maximize the performance of your amplifier, we suggest the use of a reserve power 

"Stiffening"capacitor.

         

Wiring the Amplifier

CAUTION:

 Avoid running power wires near the low level input cables, antenna, power leads, sensitive 

equipment or harnesses. The power wires carry substantial current and could radiate noise into the 

audio system through the audio cables.

         

1)

   Plan the wire routing as described in the “Importance of Pre-Plan-

ning” section. Keep RCA cables close together but isolated from 

the amplifier’s power cables and any high power auto accessories, 

especially electric motors. This is done to prevent coupling the 

noise from radiated electrical fields into the audio signal. 

When feeding the wires through the firewall or any 

metal  barrier,  protect  them  with  plastic  or  rubber 

grommets to prevent short circuits. Leave the wires 

long at this point to adjust for a precise fit at a later 

time.

2)

    Prepare the power wire for attachment to the amplifier 

by stripping 5/8 inch (15.9mm) of insulation from the 

end of the wire. Insert the bare wire into the B+ ter-

minal and tighten the set screw to secure the cable 

in place. 

 

NOTE: 

The B+ cable MUST be fused 18” or less from 

the vehicle’s positive battery post. Choose a location 

to  install  a  waterproof  fuseholder  under  the  hood 

and ensure connections are water tight. If you do not 

use the appropriate fuseholder, the connection will 

eventually suffer corrosion from moisture and heat.

Install 

Main Fuse near 

Battery

Wait to insert 

fuse until last

Upgraded Ground

Grommet in 

Firewall

Summary of Contents for D1 250.2













Reviews: