manualshive.com logo in svg

Diamond Products Fast-Cut FC7312, Instruction Manual

Share
Download
Diamond Products Fast-Cut FC7312 Instruction Manual Download Page 1

Instruction Manual

Important: 

Read this instruction manual carefully before putting the Fast-Cut into operation and strictly observe the safety regulations!

Improper use can cause serious injury! Keep this instruction manual!

WARNING!

FUELS WITH MORE THAN 10% ETHANOL ARE NOT APPROVED FOR USE IN DIAMOND PRODUcTS  

2-STROKE ENGINES!

Use of alternative fuels, such as E-20 

(20% ethanol)

, E-85 

(85% ethanol)

 or any fuels not meeting Diamond Products  

requirements are not approved for use in Diamond Products 2-stroke gasoline engines!

USE OF ALTERNATIVE FUELS cAN cAUSE THE FOLLOWING PROBLEMS:

Poor engine performance, loss of power, overheating, fuel vapor lock, improper clutch engagement, premature  

deterioration of fuel lines, premature deterioration of gaskets, premature deterioration of carburetors.

USING ALTERNATIVE FUELS AND/OR 2-STROKE OILS NOT AccORDING TO JASO Fc OR ISO-L-EGD IN  

DIAMOND PRODUcTS 2-STROKE ENGINES WILL VOID YOUR ENGINE WARRANTY!

Model Fc7312

Model Fc7314

Model Sc-8116XL

Summary of Contents for Fast-Cut FC7312

































Reviews:

No comments

Brands by name

Popular brands

Load more brands