background image

1

FEATURES

TECHNICAL

?

Symmetrical Topology, Fully Regulated, Triple-Split-Rail Power Supply

?

Isolated Input Section Utilizing “Quasi-Differential”
Instrumentation Amplifier Technology

?

Up to 12VRMS Input Signal Voltage Capability (with -12dB Attenuator)

?

Third-Order 18dB/Octave Butterworth Crossover Topology

?

Wide Bandwidth/Low Distortion Symmetrical Gain Output Stage

?

3 oz. Gold Plated Copper Circuit Board

?

High Efficiency Forced-Air Cooling System

?

Massive 3-Piece Proprietary Heatsink

?

Solid Copper High-Current Power Distribution Busbars

CONVENIENCE / APPEARANCE

?

Three 3-Way Fully Variable And Independent Electronic Crossovers
in Top-Mount Configuration With Supplied Plexiglass Security Cover

?

Assignable Crossover Inputs

?

24-Karat Gold Plated Solid Brass Circuit Board Mounted 4 Gauge
Direct or Ring Terminal Power/Ground Connector Blocks

?

24-Karat Gold Plated Solid Brass Circuit Board Mounted 10 Gauge Direct
or Banana Plug Direct Speaker Connectors

?

Tinted Plexiglas Circuit Board Viewing Panel

?

Solid Billet CNC Machined End Panels with Adjustable
Mounting Flanges

SPECIFICATIONS

Frequency Response:

3 – 50,000 Hz

Signal-to-Noise Ratio:

102dB

THD:

0.02%

Channel Separation:

80dB

Input Sensitivity:

.5 to 12VRMS

Input Impedance:

>40kOhms

Power Supply Operating Range:

10 to 16VDC

DIMENSIONS

D7056 Dimensions

Length:

22 3/4"

Width:

10 5/8"

Height:

3"

20

SYSTEM DIAGRAM 4

Four Channel Fully Active

System with Subwoofers

D7 six channel amplifier

?

Front RCA outputs of source to
channels 1/2 Highpass to tweeters

?

Channel 3/4 INPUT SELECT button “IN”

?

Channels 3/4 Bandpass to midrange drivers

?

Rear RCA outputs of source to channels 5/6
Highpass to rear fill coaxial components

D7 2 channel amplifier

?

Subwoofer RCA outputs of source
to channels 1/2 Lowpass to a pair of
bridged 8 Ohm subwoofers

Summary of Contents for D7056











Reviews: